[ForSale-Swap] FS: Miscellaneous parts

Thu Apr 8 14:31:25 EDT 2004

***  MISCELLANEOUS ***

4" Silicon wafers, etched, low yield rejects or they wouldn't be here
but, pretty -- $10 ea.

Antique boxes
  DM-36-D Dynamotor spare brush box -- $2
  Bliley BC3 Crystal, includes data sheet.  Top rough. -- $5
  Continental Carbomite Resistors -- $5

Sperry (Burroughs) SP-334 2½ Digit 7 Segment Gas Discharge Readouts.  NOS
$10 ea.  3 for $25

NOS coily cable for a Yaesu MH-27 mike (may fit others).  Later version
with the RJ connector at the radio end.  $10.

Motorola Mobile Mike Cable part number 0180700T14, 4-wire coily cord mike
cable with a Motorola 4-pin Microphone connector (similar to Amphenol
MC4M) on one end and a spring strain relief on the other.  There are some
flat pins on the free wire ends -- New in Motorola plastic bag.  $10.

NOS fan that fits some Japanese radio...marked:  57 10.01  100V
  The wires from the motor are about 4' long and are terminated in a 2
pin JST connector.  The impeller has 8 blades and is 7 cm in diameter.
  It is mounted to a U shaped metal frame with four mounting holes spaced
5cm by 9cm $10

SpeedX code key with a rectangular base.  Small crack in left
pillar casting does not affect functionality.  $10

Morse Code Key with tune lever.  Made in Japan.  $10

AEG Stepper Relay: 3 pole, 12 position, with a 48VDC coil.  New in
packing. $10

Amphenol MS connectors -- 3 pairs MS20-1 14 pin military style connectors
3 male panel connectors + 3 female cable connectors with shells (two
straight, one 90 degree); some new, some used but clean.  $10 all

Large (uncased) display unit.  256, T-1 3/4, red LED's arranged in a 16 x
16 pattern that is about 5" square.  There is a 6" x 6" mother board plus
16 daughter boards holding the LED's.   The LED's are driven by latches
so any/all of them can be lit.  There is a 14 pin DIP interface connector
-- pin out provided.   $65. 

DPDT Crystal Can relays with 600ohm 28V coils and 2A 28V contacts  made
by Leach, Datron and other manufacturers.  They have small solder hook
pins for connection and a pair of ears on the sides to mount the relay. 
These are old but, as they are hermetically sealed, they should be like
new inside! NOS $3 ea (a dozen or so available)

Carter Radio 500K ohm rheostat with 2" diameter skirted knob, calibrated
0-100 over 270 degrees -- $10

Motorola TLN6824A Vibrasender -- Freq. 1B,  107.2 Hz   $2

Motorola TLN1361A Timeout Timer $2

Sperry Gyroscope bearings? part no. 165899.  10 pieces packed in oil in a
glass bottle sealed with black glop in June 1944.  $10

Craftsman (Atlas) lathe screw for a 54" bed (36" work space) lathe. 
Used, good condition.  $100  

Trav-A-Dial bidirectional electronic counter -- I think this was
originally for use with a mill or lathe in conjunction with a 200
count/rev quadrature encoder (which I DON'T have but are available from
many sources) to read displacement in .0005" increments up to 200 inches.
These use Hewlett Packard dot matrix decimal readouts for a very pretty
display.  Switches for direction control and reset.  Nice cast metal
case, requires 5 volts power, 6 pin female Jones connector interface w/
pinout provided.   $75 

   Used, tested HP 5082-7300 RHDP decimal readouts  -- $5 ea
   Used, tested HP 5082-7304 +/-1 decimal readouts  -- $3 ea

   NOS 5082-7302 LHDP decimal readouts, still in HP packaging, $10 ea.

Listed below are serious squirrel cage type fans:

ILG Electric Ventilation 17-18-022A encased motor with 181-009-EA fan
115/230 VAC  1.6A/.8A  50/60Hz  3000 RPM  4+" round intake, 3+" x 4-3/4"
rectangular output flange, weighs 25 lbs.  used -- $30 

Kooltronic Model DF1F016N Dual fan style 230 VAC  1.2A  60Hz  3000 RPM 
3+" round intakes, 2.5" x 5" rectangular output flanges, 16" long by
about 7" diameter overall, weigh 15 lbs.   These look like NOS but,
they are a mite dusty from storage -- $25 ea (3 available)  

Commercially made airflow switch assembly consisting of a V4-16 (is that
a Cherry number?) microswitch (250VAC  5A contact rating) with a 1-3/8" x
1-3/4" sheet metal vane soldered to the switch arm.  The switch is
mounted in a U shaped anodized aluminum frame about 2.5" deep with
mounting ears.  Marked S-101 and part no. 467-115 if anyone knows where
that's from!  NOS $10

All of the above plus shipping, if necessary, naturally.

Contact:  Marv  WC6W   310 649 3111 (reasonable hours Pacific Time
please) 
or via:  Marv_E_Ads at Juno.com

* 

________________________________________________________________
The best thing to hit the Internet in years - Juno SpeedBand!
Surf the Web up to FIVE TIMES FASTER!
Only $14.95/ month - visit www.juno.com to sign up today!