[ForSale-Swap] FS: Roller Coils, B&W coils,

[marv_e_ads at juno.com]

*****  Roller Coils  ******

These two coils are shown at:
http://photos.yahoo.com/bc/marv_email/vwp?.dir=/Jpegs&.dnm=Rollers.jpg&.s
rc=ph&.view=t&.hires=t

Johnson 229-202 18uH  used good, $50

La Pointe L-0201 406-1 (identical to a Johnson 229-201) 10 uH. used good,
$30


*****   B&W Air Dux coils  *****

These are NOS, 10" lengths, unless noted otherwise  Many are in the photo
at:
http://photos.yahoo.com/bc/marv_email/vwp?.dir=/Jpegs&.dnm=bwcoils.jpg&.s
rc=ph&.view=t&.hires=t

#2008-31  2.5"dia x 4" long , 8TPI, #14 wire with 2 turn #14 link at
center. NIB  $25

#1208T  1.5" dia,  8TPI, #16 wire, slight tarnish   $20
#1216T  1.5" dia,  16TPI, #20 wire, somewhat tarnished   $20
#1006T  1.25" dia,  6TPI, #14 wire, somewhat tarnished   $15

plus a NOS partial length

#1008T   1.25" dia, 8 TPI, #16 wire, 8" long -- $12

--- some other partial lengths

#2408T   3" dia, 8 TPI, #14 wire, 6" long shiny -- $20
#2408T   3" dia, 8 TPI, #14 wire, 4" long shiny -- $15
#2410T   3" dia, 10 TPI, #14 wire, 2.5" slightly tarnished -- $10

--- some Miniductors

#3030   2.5"" dia, 8 TPI, #14 wire, 4" tarnished -- $10
#3031   2.5"" dia, 10 TPI, #16 wire, 3" long somewhat tarnished -- $10
#3031   2.5"" dia, 10 TPI, #16 wire, 1.75" long somewhat tarnished -- $5

---a couple of Illumintronic Engineering parts

375 7367-P1 -- 1.5" dia.x  5.75" winding w/ indented turns, 14 TPI, #17,
7" overall 
   including plastic center support, un-used somewhat tarnished   $25

 980-0121-000 --  2.5" dia. x 7.5" winding w/ indented turns, 8 TPI, #14,
9.5" overall 
   including plastic center support, used somewhat tarnished but, no
turns soldered   $30

--- some other coils:

6.5 turns, 2" diameter 2" long silver plated .185" diameter copper tubing
-- currently tarnished but, should clean up nice -- $15

6 turns, 2.5" diameter 2" long silver plated .25" diameter copper tubing
-- lightly tarished.  Ends are flatteded to one inch long tabs with a
hole for say a #10 screw.  There is a crack in the tubing near one
termination which may be easily repaired with silver solder.  -- $20


---  A couple large old RF chokes, may be seen at:
http://photos.yahoo.com/bc/marv_email/vwp?.dir=/Jpegs&.dnm=rfc.jpg&.src=p
h&.view=t&.hires=t

  #22 enameled wire space wound 24 TPI for 2.75 on a 1" diameter grooved
fiberglass form 5" overall -- $5

  ART-13 choke? -- #27 (green enameled) wire wound 40 TPI for 4.3" on a
3/4" diameter ceramic form which steps to a 1.3" diameter base tapped for
two 6-32 screws, 5.5" long 
overall.  Looks like winding has been cleanly spliced, twice -- $7


All of the above plus shipping, if necessary, naturally.

Contact:  Marv  WC6W   310 649 3111 (reasonable hours Pacific Time
please) 
or via:  Marv_E_Ads at Juno.com




*

________________________________________________________________
GET INTERNET ACCESS FROM JUNO!
Juno offers FREE or PREMIUM Internet access for less!
Join Juno today!  For your FREE software, visit:
http://dl.www.juno.com/get/web/.