[Elecraft] Elecraft Digest, Vol 270, Issue 13
carlos popelier
carlos.on6cn at gmail.com
Thu Oct 15 14:50:07 EDT 2026
sorry, high 12099 low 12085
73
Op do 15 okt 2026 om 20:48 schreef carlos popelier <carlos.on6cn at gmail.com>:
>
> hi,ref oscillator high 121099 low 12085
> vco test most be between 8-10 mhz reading 09149
> 73
>
> Op wo 14 okt 2026 om 18:03 schreef <elecraft-request at mailman.qth.net>:
> >
> > Send Elecraft mailing list submissions to
> > elecraft at mailman.qth.net
> >
> > To subscribe or unsubscribe via the World Wide Web, visit
> > http://mailman.qth.net/mailman/listinfo/elecraft
> > or, via email, send a message with subject or body 'help' to
> > elecraft-request at mailman.qth.net
> >
> > You can reach the person managing the list at
> > elecraft-owner at mailman.qth.net
> >
> > When replying, please edit your Subject line so it is more specific
> > than "Re: Contents of Elecraft digest..."
> >
> >
> > Today's Topics:
> >
> > 1. ALC (Josep)
> > 2. Re: ALC (mgcizek at gmail.com)
> > 3. Re: ALC (Michael Carter)
> > 4. FS: Elecraft KPA1500 (n5zm n5zm.net)
> > 5. Re: k2 vco voltage (Michael Carter)
> > 6. K4D drastic decrease in TX Line In level on FT8 (John Klewer)
> >
> >
> > ----------------------------------------------------------------------
> >
> > Message: 1
> > Date: Tue, 13 Oct 2026 17:26:32 +0000 (UTC)
> > From: Josep <ea6bf at aol.com>
> > To: Elecraft Email List <elecraft at mailman.qth.net>
> > Subject: [Elecraft] ALC
> > Message-ID: <438218241.1867059.1791912392581 at mail.yahoo.com>
> > Content-Type: text/plain; charset=UTF-8
> >
> > Hi guys,
> > I have a question for you...
> > When I switch on my K3, it automatically puts in ALC mode.My other K3 do not do that, what can I do to avoid that when I switch on my radio.?
> > Thank you.
> > 73,?
> > JosepEA6BFhttp://www.ea6bf.com
> > EF6B (Contest Callsign)
> > CW Academy Fundamental AdvisorBUG #256? -??CWOps #3072? -??FOC #2182 (ex 1724)? -? CTDXCC? -? HSC #2016? -? VHSC #441? -? SMHSC #246? -? UQRQC #191? -? OECWG #147
> >
> > ------------------------------
> >
> > Message: 2
> > Date: Tue, 13 Oct 2026 12:40:46 -0500
> > From: <mgcizek at gmail.com>
> > To: "'Josep'" <ea6bf at aol.com>, "'Elecraft Email List'"
> > <elecraft at mailman.qth.net>
> > Subject: Re: [Elecraft] ALC
> > Message-ID: <[email protected]>
> > Content-Type: text/plain; charset="UTF-8"
> >
> > Hello Josep,
> >
> > In the CONFIG menu, turn TX ALC off.
> >
> > ---
> > 73,
> > Mike Cizek W?VTT
> >
> > -----Original Message-----
> > From: elecraft-bounces at mailman.qth.net <elecraft-bounces at mailman.qth.net> On Behalf Of Josep via Elecraft
> > Sent: Tuesday, 13 October, 2026 12:27
> > To: Elecraft Email List <elecraft at mailman.qth.net>
> > Subject: [Elecraft] ALC
> >
> > Hi guys,
> > I have a question for you...
> > When I switch on my K3, it automatically puts in ALC mode.My other K3 do not do that, what can I do to avoid that when I switch on my radio.?
> > Thank you.
> > 73,
> > JosepEA6BFhttp://www.ea6bf.com
> > EF6B (Contest Callsign)
> > CW Academy Fundamental AdvisorBUG #256 - CWOps #3072 - FOC #2182 (ex 1724) - CTDXCC - HSC #2016 - VHSC #441 - SMHSC #246 - UQRQC #191 - OECWG #147 ______________________________________________________________
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft at mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html Message delivered to mgcizek at gmail.com
> >
> >
> >
> > ------------------------------
> >
> > Message: 3
> > Date: Tue, 13 Oct 2026 21:41:39 +0000
> > From: Michael Carter <Mike.Carter at unh.edu>
> > To: Elecraft Reflector Reflector <elecraft at mailman.qth.net>
> > Subject: Re: [Elecraft] ALC
> > Message-ID:
> > <PH7P223MB1097740DDDBBC7990BA48927E49E2 at PH7P223MB1097.NAMP223.PROD.OUTLOOK.COM>
> >
> > Content-Type: text/plain; charset="iso-8859-1"
> >
> > Hi Josep,
> >
> > Press the METER button to go from COMP/ALC back to SWR/Power display.
> >
> > 73,
> > Mike, K8CN
> >
> >
> > ------------------------------
> >
> > Message: 4
> > Date: Tue, 13 Oct 2026 23:54:57 +0000
> > From: "n5zm n5zm.net" <n5zm at n5zm.net>
> > To: Elecraft <elecraft at mailman.qth.net>, "Elecraft-K4 at groups.io"
> > <Elecraft-K4 at groups.io>
> > Subject: [Elecraft] FS: Elecraft KPA1500
> > Message-ID: <a7d42041-6a45-4c04-8885-20ad6c09d382 at n5zm.net>
> > Content-Type: text/plain; charset="utf-8"
> >
> >
> > Re-Post. Price reduction.
> >
> > Closing station (N5ZM) here after 50 years of memories. I will be moving to a retirement village. (Age 83)
> >
> > Towers and antennas are down the K4D is sold so time to let go.
> >
> > For Sale is my KPA1500 S/N 02xx. $5500 Plus Shipping. (Will Deliver inside Arkansas)
> >
> > Amp works well with most popular radios.
> >
> > I have the original Boxes cables and Manual.
> >
> > Amp is clean, non-smoking and was on the air right up to when I closed the station.
> >
> > Earl N5ZM [n5zm at n5zm.net<mailto:n5zm at n5zm.com>]
> >
> >
> >
> > ------------------------------
> >
> > Message: 5
> > Date: Wed, 14 Oct 2026 01:25:41 +0000
> > From: Michael Carter <Mike.Carter at unh.edu>
> > To: Elecraft Reflector Reflector <elecraft at mailman.qth.net>
> > Cc: Andrew Lenton <a at lenton.org>
> > Subject: Re: [Elecraft] k2 vco voltage
> > Message-ID:
> > <PH7P223MB1097BB87651999E3460EDA11E49D2 at PH7P223MB1097.NAMP223.PROD.OUTLOOK.COM>
> >
> > Content-Type: text/plain; charset="iso-8859-1"
> >
> > Hi Carlos,
> >
> > After reviewing your description of the sequence of band failures (inability to receive and transmit on selected bands) over time, I have an idea.
> >
> > I would first verify using the K2 internal frequency counter that the PLL reference oscillator is working and generating a signal In the 12.090 MHz - 12.100 MHz range. This should be true regardless of the band selected. If there is no signal at TP3, where the PLL reference oscillator feeds the divider/phase detector chip, then we can concentrate on getting the reference oscillator working.
> >
> > If you do have a signal at TP3 in the correct frequency range, then we can investigate the rest of the loop.
> >
> > You described first losing reception on the 20 meter band, then lost 40 and 80 meters, then all bands ceased to provide reception - is that sequence correct?
> >
> > There are two critical actions that need to take place to generate the correct VCO output frequency: (a) the MCU needs to interpret the band select and the tuning encoder to generate the correct programming words for the PLL chip, and (b) the MCU needs to send the proper code to the IO controller (U1 on the RF board) to activate the proper relays for the selected band. If either of those actions fail, then the VCO will revert to its free-running frequency because the loop will fail to lock. The voltage at R30 will go to one of the extreme values you measured (8V or ~ 3V).
> >
> > The additional fixed and variable (varactors D21 and D22) capacitances that are switched into the VCO circuit are controlled by relays K13, K14, and K15. On 20 meters, all three relays are switched to the SET position. On 80 meters, only K13 is set. On 40 meters, presuming you do NOT have the K60XV option installed, relays K13 and K14 are set. On other bands various combinations of K13, K14 and K15 are set to provide proper tuning capacitance.
> >
> > What I am beginning to suspect is one of two causes:
> >
> > 1.
> > The IOC is not receiving a valid code sequence from the MCU due to AUXBUS problems, or
> > 2.
> > The IOC has developed a problem(s) on the three relay driver pins for K13, K14, and K15.
> >
> > Without a logic analyzer or some tedious inspection of AUXBUS captures at the IOC input, it would be difficult to know if the MCU is sending proper programming words to the PLL chip. However, it is possible to verify if the proper relays are activated for a given band by feeling with your finger each of the relays K13, K14, and K15 as you switch from band to band. The relay table in Appendix B of the K2 manual gives the relays activated on each band (relays are normally in RESET position, and are SET according to the selected band.
> >
> > If the PLL reference oscillator has failed, that should be easily detected using the K2 internal frequency counter at TP3. Don, W3FPR has identified the J310 at Q19 as a frequent cause of PLL reference failure, although I don't understand how a succession of individual band failures over time could be caused by changing JFET characteristics over time, especially since Q19 is tuned over a very narrow range regardless of selected band.
> >
> > If the activated relays K13, K14, and K15 do not properly correspond to the selected band, but the MCU does provide the correct PLL divider programming words for that band and band segment, then the loop will fail to lock. The VCO will revert to some free-running frequency that may still enable band noise to be heard, but no signals will be heard because of mismatch of the VCO relays and BPF/LPF relay settings.
> >
> > Please let us know what you find for these two suggested tests.
> >
> > 73,
> > Mike, K8CN
> >
> >
> > ------------------------------
> >
> > Message: 6
> > Date: Wed, 14 Oct 2026 08:44:59 -0700
> > From: John Klewer <n6axjohn at gmail.com>
> > To: "elecraft at mailman.qth.net" <Elecraft at mailman.qth.net>
> > Subject: [Elecraft] K4D drastic decrease in TX Line In level on FT8
> > Message-ID:
> > <CAAFJj=qgZPGugitwDxK9VMGM10sM2onOiW3jSTL0fmJaq_6gPw at mail.gmail.com>
> > Content-Type: text/plain; charset="UTF-8"
> >
> > K4D, SN 386, running FT4/8 on Mac-Mini.
> > Line in level was 35 and all worked great.
> > I downloaded JTDX to try it and now WSJT-X requires LINE In level of 250!
> >
> > I have gone over all the computer's audio settings and insured that audio
> > is being steered to WSJT-X....I have not yet uninstalled JTDX but it is
> > "off".
> >
> > Suggestions, please?
> >
> > John, N6AX
> >
> >
> > ------------------------------
> >
> > _______________________________________________
> > Elecraft mailing list
> > Post to: Elecraft at mailman.qth.net
> > http://mailman.qth.net/mailman/listinfo/elecraft
> > You must be a subscriber to post.
> > Elecraft web page: http://www.elecraft.com
> >
> > End of Elecraft Digest, Vol 270, Issue 13
> > *****************************************
>
>
>
> --
> mvg carlos popelier
> regards carlos popelier
--
mvg carlos popelier
regards carlos popelier
More information about the Elecraft
mailing list