[Elecraft] k2 vco voltage

Andrew Lenton a at lenton.org
Thu Oct 15 10:07:44 EDT 2026


Hi Carlos, 
  
  
  
  
  Have managed to measure the 12.096 MHz Osc yet? 
  
  
  
  
  KR 
  
  
  
  
  Andrew  
  
  
  
  
  
  
  
  
  
  
  


  
  
Hi Carlos, 
  
  
  
  
  
  
  
  
  
After reviewing your description of the sequence of band failures 
(inability to receive and transmit on selected bands) over time, I have an 
idea. 
  
  
  
  
  
  
  
  
  
I would first verify using the K2 internal frequency counter that the PLL 
reference oscillator is working and generating a signal In the 12.090 MHz - 
12.100 MHz range.  This should be true regardless of the band selected. If 
there is no signal at TP3, where
  the PLL reference oscillator feeds the divider/phase detector chip, then 
we can concentrate on getting the reference oscillator working. 
  
  
  
  
  
  
  
  
  
If you do have a signal at TP3 in the correct frequency range, then we can 
investigate the rest of the loop. 
  
  
  
  
  
  
  
  
  
You described first losing reception on the 20 meter band, then lost 40 and 
80 meters, then all bands ceased to provide reception - is that sequence 
correct? 
  
  
  
  
  
  
  
  
  
There are two critical actions that need to take place to generate the 
correct VCO output frequency: (a) the MCU needs to interpret the band 
select and the tuning encoder to generate the correct programming words for 
the PLL chip, and (b) the MCU needs to send
  the proper code to the IO controller (U1 on the RF board) to activate the 
proper relays for the selected band.  If either of those actions fail, then 
the VCO will revert to its free-running frequency because the loop will 
fail to lock.  The voltage at R30
  will go to one of the extreme values you measured (8V or ~ 3V). 
  
  
  
  
  
  
  
  
  
The additional fixed and variable (varactors D21 and D22) capacitances that 
are switched into the VCO circuit are controlled by relays K13, K14, and 
K15.  On 20 meters, all three relays are switched to the SET position.  On 
80 meters, only K13 is set.  On 40
  meters, presuming you do NOT have the K60XV option installed, relays K13 
and K14 are set.  On other bands various combinations of K13, K14 and K15 
are set to provide proper tuning capacitance. 
  
  
  
  
  
  
  
  
  
What I am beginning to suspect is one of two causes:  
  
  
  
  
  The IOC is not receiving a valid code sequence from the MCU due to AUXBUS 
problems, or 
  
  
  
  The IOC has developed a problem(s) on the three relay driver pins for 
K13, K14, and K15. 
  
  
  
  
  
  
  
  
  
  
Without a logic analyzer or some tedious inspection of AUXBUS captures at 
the IOC input, it would be difficult to know if the MCU is sending proper 
programming words to the PLL chip.  However, it is possible to verify if 
the proper relays are activated for
  a given band by feeling with your finger each of the relays K13, K14, and 
K15 as you switch from band to band.  The relay table in Appendix B of the 
K2 manual gives the relays activated on each band (relays are normally in 
RESET position, and are SET according
  to the selected band. 
  
  
  
  
  
  
  
  
  
If the PLL reference oscillator has failed, that should be easily detected 
using the K2 internal frequency counter at TP3.  Don, W3FPR has identified 
the J310 at Q19 as a frequent cause of PLL reference failure, although I 
don't understand how a succession
  of individual band failures over time could be caused by changing JFET 
characteristics over time, especially since Q19 is tuned over a very narrow 
range regardless of selected band. 
  
  
  
  
  
  
  
  
  
If the activated relays K13, K14, and K15 do not properly correspond to the 
selected band, but the MCU does provide the correct PLL divider programming 
words for that band and band segment, then the loop will fail to lock.  The 
VCO will revert to some free-running
  frequency that may still enable band noise to be heard, but no signals 
will be heard because of mismatch of the VCO relays and BPF/LPF relay 
settings. 
  
  
  
  
  
  
  
  
  
Please let us know what you find for these two suggested tests. 
  
  
  
  
  
  
  
  
  
73, 
  
  
  
Mike, K8CN


More information about the Elecraft mailing list