[Elecraft] Elecraft Digest, Vol 270, Issue 11

carlos popelier carlospopelier at hotmail.com
Mon Oct 12 12:24:17 EDT 2026


after 10 years, first loss of  20m band, then gradually worse, loss of all bands, sometimes vco 3volt and then sometimes 8volt, main ic control and rf board are ok, swapped them from my working one,somethimes info 080,not always.....

Verzonden vanaf Outlook voor Android<https://aka.ms/AAb9ysg>
________________________________
From: elecraft-bounces at mailman.qth.net <elecraft-bounces at mailman.qth.net> on behalf of elecraft-request at mailman.qth.net <elecraft-request at mailman.qth.net>
Sent: Monday, 12 October 2026 18:00:16
To: elecraft at mailman.qth.net <elecraft at mailman.qth.net>
Subject: Elecraft Digest, Vol 270, Issue 11

Send Elecraft mailing list submissions to
        elecraft at mailman.qth.net

To subscribe or unsubscribe via the World Wide Web, visit
        http://mailman.qth.net/mailman/listinfo/elecraft
or, via email, send a message with subject or body 'help' to
        elecraft-request at mailman.qth.net

You can reach the person managing the list at
        elecraft-owner at mailman.qth.net

When replying, please edit your Subject line so it is more specific
than "Re: Contents of Elecraft digest..."


Today's Topics:

   1. Elecraft 80M SSB Net Announcement (Dave New, N8SBE)
   2.  k2 vco voltage (Andrew Lenton)
   3. Re: k2 vco voltage (Michael Carter)
   4. Elecraft 80M SSB Net Report (Dave New, N8SBE)
   5. Elecraft CW Net Report for Sunday, October 11, 2026 (brian hunt)
   6. Re: k2 vco voltage (Andrew Lenton)
   7. For sale: E850463 cable (Carl Yaffey)


----------------------------------------------------------------------

Message: 1
Date: Sun, 11 Oct 2026 13:27:45 -0400
From: "Dave New, N8SBE" <n8sbe at densbe.com>
To: Elecraft Reflector <elecraft at mailman.qth.net>, Elecraft K4
        <Elecraft-K4 at groups.io>, Main <main at elecraft-kx.groups.io>
Subject: [Elecraft] Elecraft 80M SSB Net Announcement
Message-ID: <8b738ae89d7fdbd5c975c98b38cea860 at densbe.com>
Content-Type: text/plain; charset=US-ASCII; format=flowed

Please join us on 3803kHz plus (not minus) QRM (see the Netlogger
discussion, below), 9PM ET Sunday (0100Z Monday). Note that the net
stays on the same local time, when we switch back and forth to/from
Daylight time, so the UTC time changes, but not the local time.

Your net control for this week is Dave, N8SBE.

The group that meets on 3803 kHz before us has been wrapping up
operations promptly at or before 9PM ET.  There is also another group
that normally comes on at 10PM ET, so we need to make sure to wrap up
operations by 10PM ET.  If any stations wish to continue past that time,
please QSY to a clear frequency.

If you are a US General class licensee, please ensure that your dial is
accurately calibrated and that your transmitter/amplifier combination is
clean and free of splatter, since we will be operating LSB within 3 kHz
of the lower band edge of the 80M US General class band.

If we find 3803 kHz busy, we will move UP the band a few kHz, so we can
stay in the 80M US General class band.

Hope to see you this evening on the net.

73,

-- Dave, N8SBE, Hamshack Hotline RIP, HamsOverIP 101018, AmateurWire
1348

------------------------------

Message: 2
Date: Sun, 11 Oct 2026 21:49:56 +0000
From: Andrew Lenton <a at lenton.org>
To: elecraft-request at mailman.qth.net, elecraft at mailman.qth.net
Subject: [Elecraft]  k2 vco voltage
Message-ID: <8214011ccb0ae8.394914695e7ffc at lenton.org>
Content-Type: text/plain; charset=utf-8

Hi is this a new build or developed a fault or never worked?




 KR




 Andrew









 Send Elecraft mailing list submissions to

 ?elecraft at mailman.qth.net




 To subscribe or unsubscribe via the World Wide Web, visit

 ?http://mailman.qth.net/mailman/listinfo/elecraft

 or, via email, send a message with subject or body 'help' to

 ?elecraft-request at mailman.qth.net




 You can reach the person managing the list at

 ?elecraft-owner at mailman.qth.net




 When replying, please edit your Subject line so it is more specific

 than "Re: Contents of Elecraft digest..."







 Today's Topics:




    1. k2 vco voltage (carlos popelier)












 Message: 1

 Date: Sat, 10 Oct 2026 18:11:38 +0200

 From: carlos popelier <carlos.on6cn at gmail.com>

 To: elecraft at mailman.qth.net

 Subject: [Elecraft] k2 vco voltage

 Message-ID:

 ?<CAKqkSC2WZ=8oeH-8EfD=UcA9=EyR1RgpSgdOy+ATGPwbvqOsRQ at mail.gmail.com>

 Content-Type: text/plain; charset="UTF-8"




 problem with k2 not receiving, 6v voltage not present or adjustable at r30

 first only 80m en 40m working,getting worse all bands stopped, on r 30

 voltage was + - 8v not adjustable, then 3,5v not adjustable, menus are

 working, no error messages, audio is working, any ideas where to start

 measuring.....







 mvg carlos popelier

 regards carlos popelier












 _______________________________________________

 Elecraft mailing list

 Post to: Elecraft at mailman.qth.net

 http://mailman.qth.net/mailman/listinfo/elecraft

 You must be a subscriber to post.

 Elecraft web page: http://www.elecraft.com




 End of Elecraft Digest, Vol 270, Issue 10

 *****************************************

------------------------------

Message: 3
Date: Mon, 12 Oct 2026 00:30:56 +0000
From: Michael Carter <Mike.Carter at unh.edu>
To: Elecraft Reflector Reflector <elecraft at mailman.qth.net>
Cc: Andrew Lenton <a at lenton.org>
Subject: Re: [Elecraft] k2 vco voltage
Message-ID:
        <PH7P223MB10970769DECBC94882C4EA54E4902 at PH7P223MB1097.NAMP223.PROD.OUTLOOK.COM>

Content-Type: text/plain; charset="iso-8859-1"

Hi Carlos,

When the voltage at R30 went to +8V, that indicates that the op amp U6B went to its positive rail.  U6B has no DC feedback path to stabilize its output at DC, and the output range center is biased to +4V by the fixed voltage at the non-inverting terminal (pin 5 of U6).  Since U6B is configured as an inverting op amp, the railed output indicates that the phase detector output (pin 13, U4) was producing a lot of negative-going pulses, which when filtered by the RC lowpass filter gave rise to a low average (DC) voltage to the U6B inverting input.  The phase detector of the MC145170 supplies negative pulses when the frequency of the (divided) loop VCO is less than the frequency of the reference oscillator, i.e. the PLL is not locked.

There can be many reasons for the loop failing to lock.  Once U6B goes to one of its rails, the VCO frequency is fixed at whatever value corresponds to the applied tuning voltage on the varactors (D23/D24/D25/D26) on the selected band.  L30 will have little or no effect if that frequency is too far removed from the lock range of the PLL.

As Andrew asked, under what conditions did you first notice failure of the PLL/VFO system?

73,
Mike, K8CN




------------------------------

Message: 4
Date: Sun, 11 Oct 2026 22:04:16 -0400
From: "Dave New, N8SBE" <n8sbe at densbe.com>
To: Elecraft Reflector <elecraft at mailman.qth.net>, Elecraft K4
        <Elecraft-K4 at groups.io>, Main <main at elecraft-kx.groups.io>
Subject: [Elecraft] Elecraft 80M SSB Net Report
Message-ID: <7f697ae2624f1743e4aa700048fef45a at densbe.com>
Content-Type: text/plain; charset=US-ASCII; format=flowed

3803 kHz, 9PM ET Sunday (currently 0100Z Monday).

Thanks to the following check ins (w) and relays (rel):

    Call     St    Radio/Amp                        Name
1  N8SBE    MI    K4D/KPA500 remote via K4/0       Dave
(nc),(log),(w),(op)
2  K5WC     AR    K4D/Mercury Lux                  John  (rel),(w)
3  WB9JNZ   IL    FTdx101d/KPA1500                 Eric  (rel),(w)
4  KB4JHU   TN    KX3 15W                          Mike  (w)
5  K8CGS    MI    K4D/KPA500                       Greg  (w)
6  KD8RV    MI    K3/KPA1500                       Greg  (w)
7  WM6P     GA    K4D/KPA1500                      Steve  (rel),(w)
8  K4TM     VA    IC-7300                          Cary  (c/o),(p),(w)
9  W9PCS    WI    K4D/KPA500                       Paul  (w)
10 WW4JF    TN    K3s/KPA500                       John  (w)
11 KB3HJC   PA    KX3 15W                          Randy  (w)

(Entries with (c/o) indicate a 'one and done' station that checked out
during the 1st round. (n/h) failed to respond during initial (was only
checked into Netlogger) or subsequent rounds. (p) indicates a portable
station. (m) indicates a mobile station.  Callsigns with an asterisk '*'
are re-checks, in this case via remote stations.)

We had a total of 11 check ins this week (including the NCS). Thanks to
all the stations that helped with relays (rel). I hope to see all of you
again. The net concluded at 10:00 PM ET.

We have a really great group of folks checking in, and I encourage
everyone in the Midwest and adjoining areas to check in next week.

As a reminder, if you go to https://netlogger.org at the net starting
time and look for the 80M Elecraft SSB Net, you should see the frequency
we are using that evening, if we must QSY due to busy frequencies.

Also, check out https://hams.live to find out how to set up a multi-SDR
receiver on your PC, which greatly aids in hearing folks during poor
propagation or high noise levels.

Also, also, please check out https://mikeg-dal.github.io/QK4/ for the
latest QK4 K4/K4D remote software for Windows.  This is currently Beta,
so some things are not complete, yet, but I think you will find it quite
useful.

Finally, here are a couple of URLs to the Lightning Map and the NOAA
Radio Communications Dashboard:
https://www.lightningmaps.org/
https://www.swpc.noaa.gov/communities/radio-communications

73,

-- Dave, N8SBE


------------------------------

Message: 5
Date: Sun, 11 Oct 2026 20:39:11 -0700
From: brian hunt <huntinhmb at coastside.net>
To: Elecraft Reflector <elecraft at mailman.qth.net>
Subject: [Elecraft] Elecraft CW Net Report for Sunday, October 11,
        2026
Message-ID: <f2c8b06e-3829-4aba-b8e4-cd8deb2a4230 at coastside.net>
Content-Type: text/plain; charset=UTF-8; format=flowed

The following stations checked into the Elecraft CW Nets today:

20 Meter net on 14050.8 kHz
K4TO, Dave KY
WJ7S, John UT (John was QRV with his KH1 - good signal!)
W8OV, Dave TX

40 Meter net on 7047.5 kHz
K6PJV, Dale CA
WM5F, Dwight ID
W0CZ, Ken ND? (Thanks Dave, W8OV, for the assistance on the 40 meter net.)

73,
Brian, K0DTJ


------------------------------

Message: 6
Date: Mon, 12 Oct 2026 11:36:36 +0000
From: Andrew Lenton <a at lenton.org>
To: Michael Carter <mike.carter at unh.edu>, Elecraft Reflector Reflector
        <elecraft at mailman.qth.net>, mike.carter at unh.edu
Subject: Re: [Elecraft] k2 vco voltage
Message-ID: <b916434d8208f8.557f092c8b4dd4 at lenton.org>
Content-Type: text/plain; format=flowed; charset=utf-8

My post did not go through,




  Is this a new build, failed in use or bought broken?







  KR




  Andrew















Hi Carlos,









When the voltage at R30 went to +8V, that indicates that the op amp U6B
went to its positive rail.  U6B has no DC feedback path to stabilize its
output at DC, and the output range center is biased to +4V by the fixed
voltage at the non-inverting terminal (pin
  5 of U6).  Since U6B is configured as an inverting op amp, the railed
output indicates that the phase detector output (pin 13, U4) was producing
a lot of negative-going pulses, which when filtered by the RC lowpass
filter gave rise to a low average (DC) voltage
  to the U6B inverting input.  The phase detector of the MC145170 supplies
negative pulses when the frequency of the (divided) loop VCO is less than
the frequency of the reference oscillator, i.e. the PLL is not locked.









There can be many reasons for the loop failing to lock.  Once U6B goes to
one of its rails, the VCO frequency is fixed at whatever value corresponds
to the applied tuning voltage on the varactors (D23/D24/D25/D26) on the
selected band.  L30 will have little
  or no effect if that frequency is too far removed from the lock range of
the PLL.









As Andrew asked, under what conditions did you first notice failure of the
PLL/VFO system?









73,



Mike, K8CN

------------------------------

Message: 7
Date: Mon, 12 Oct 2026 11:11:10 -0400
From: Carl Yaffey <cyaffey at gmail.com>
To: "Elecraft Mailman.QTH.net" <elecraft at mailman.qth.net>
Subject: [Elecraft] For sale: E850463 cable
Message-ID: <1A153AD1-85D3-4735-9333-B811490A6EC8 at gmail.com>
Content-Type: text/plain;       charset=us-ascii

For sale: E850463 cable.
$20
Carl Yaffey  K8NU
614 268 6353, Columbus OH
http://www.carl-yaffey.com
http://www.bluesswing.com
http://www.timbrewolvesband.com
http://www.folkramblers.carl-yaffey.com
http://WalhallaRamblers.com







------------------------------

_______________________________________________
Elecraft mailing list
Post to: Elecraft at mailman.qth.net
http://mailman.qth.net/mailman/listinfo/elecraft
You must be a subscriber to post.
Elecraft web page: http://www.elecraft.com

End of Elecraft Digest, Vol 270, Issue 11
*****************************************


More information about the Elecraft mailing list