[Elecraft] K3S interface problem with KPA500/KAT500

[Terry Conboy]

Jack,

Thanks so much for your thoughtful reply.

RADIO=K3 is set in the KPA 500.

I connected the K3S directly to the KPA500 with one of the E850463 (KPAK3AUX) cables.  The K3S still follows the KPA500, but not the other way.  I tried the other cable in its place with the same result.  Status messages from the KPA500 do appear in the K3S display.

I’m not sure what you mean about the "cut pins" on the cables.  I’m just using the stock Elecraft cables without the E850462 keying line interrupter.

Your suspicion about a problem with the K3S Aux I/O port seems well founded.  Do you know if there is any documentation about how the port signaling operates?  There are the four BCD lines (pins 3, 9, 13, & 14) and one from the K3S labeled AUXBUS (pin 2), but not much info about how the bus knows what device gets to “talk” on the bus.  I didn’t see anything on the Elecraft site, but it could be included in another manual.

Thanks & 73,
Terry N6RY

> On Apr 28, 2025, at 10:58 AM, Jack Brindle <jackbrindle at me.com> wrote:
> 
> Make sure that you have RADIO = K3 in the KPA500 menu. I suspect you do since you indicate the K3 is following the KPA500 when you press one of the band buttons on the KPA. In the KPA, RADIO must be set to either K3 or BCD for it to follow the K3 BAND signals. If it is set to K3, then the KPA will send information to the K3 when something happens. 
> 
> The KAT listens for communications from the K3 on the Aux I/O data bas, and should be changing its selector bins based on the frequency the K3 sends it.
> 
> This all makes me suspect that something is wrong with the K3’s AUX I/O port. You can (carefully) look at the voltages on the AUX cables to make sure the BAND signals are changing as they should. If not, then the issue is in the K3. 
> 
> My suggestion is to check things out one at a time. Connect the KPA500 directly to the K3 using the proper cable (this one should have pins cut at one end). You should be able to get that going without transmitting - when the K3 changes bands, the KPA should follow. This is completely due to changes in the K3’s BAND signals. Once that works, then add the KAT500 to the system. Remember, the KAT connects between the K3 and the KPA so that it can disable the PTT going to the KPA when the KAT needs to tune.
> 
> These may seem like very simple steps, but they should isolate the problem and get us closer to a working system.
> Let me know how your tests go.
> 
> 73,
> Jack, W6FB
> 
> 
>> On Apr 28, 2025, at 12:20 PM, Terry Conboy <n6ry at arrl.net> wrote:
>> 
>> I bought the 500 pair last fall and connected them to my K3S (2017 vintage) with the official Elecraft cables (which I've checked for correct pin connections and no shorts).  All three units are at current software versions.  The issue I have is that if I change bands on the K3S, nothing happens with the tuner or amp.  However, when I change bands on the KPA500, the K3S follows as expected.
>> 
>> I have the internal tuner in the K3S (disabled when using the 500 pair).  I set the CONFIG: KAT3 for KAT500Y.
>> 
>> Of course, the tuner and amp detect the TX output and switch quickly, but I’d like to have the tuner follow the K3S for WSPR receive.
>> 
>> I’ve corresponded with the customer service crew at Elecraft, but no help so far.  Anyone have any ideas about Config settings or anything else to check?
>> 
>> Thanks,
>> Terry N6RY
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to jackbrindle at me.com
>