[Elecraft] K3 & K3S Options Last Time Buy Update, (12/02/2022)

[Gary K9GS]

I think it would be great if someone would write an app to do this.While you're at it might as well fix the USB port sleeping problem too.73,Gary K9GS
-------- Original message --------From: Rick NK7I <rick.nk7i at gmail.com> Date: 12/5/22  1:04 PM  (GMT-06:00) To: elecraft at mailman.qth.net Subject: Re: [Elecraft] K3 & K3S Options Last Time Buy Update, (12/02/2022) While this article is for the K4, the exact same should be done for the K3 to stop accidental keying during boot up of the OS.I suggest that you do this for ALL of your USB ports and while you're there, also defeat (turn off, uncheck) power savings mode (once turned off, it won't restart until the next reboot, negating it's value to less than zero), again on ALL of your USB devices (hubs, ports etc).73,Rick nk7iUse Windows Device Manager (run devmgmt.msc) to change the Advanced properties of both of the K4 FTDI virtual serial ports: Uncheck Serial Enumeration Check Disable Modem Control At Startup Details and rationale here, with screenshots: https://bit.ly/FTDItipOn 12/5/2022 10:53 AM, Dave New, N8SBE wrote:> Ed,>> Likely the 'clicking' you are hearing is the PC initializing the USB > ports on boot up.> If you watch closely, you will see the K3 PTT/XMIT come on a few times > during the computer boot up.>> It's harmless, but annoying, although if I recall correctly, on CW it > actually ends up sending a carrier.>> There was a firmware update for the K3/K3S that makes it ignore those > computer PTT by leaving the VOX turned> off on CW until you transmit something (not from the computer). This > happens if you power cycle> the K3 before turning on the computer.>> Of course, you could just turn off the K3 and leave it off until the > computer finishes booting.>> I don't have an explanation as to why moving the USB cable to the > front ports seemingly has> stopped the issue.  Perhaps you just didn't happen to trigger the > issue (see above)?>> Hope that helps,>> -- Dave, N8SBE>> On 2022-12-04 16:24, Ed Cole wrote:>> Nice to hear about.>>>> I contacted sales at elecraft regarding getting on the KI03B list (more>> than a year ago) and was told, at that time I would be added.>>>> I have the KI03A (original with my K3) which Elecraft repaired about>> two years ago and has worked well, so far.  I decided I should have a>> backup so ordered the B board (A NLA).>>>> But not being one of the original list, but an add-on, I wonder if>> inventory will be sufficient to fill my order?>>>> I encountered a strange phenomena, as the K3 would constantly click>> whenever the computer I/F cable (from Elecraft) was connected and>> computer turned on.  I have 4 USB ports on rear of computer and 2 on>> front.  Moving to a front USB connector ceased the clicking. BTW the>> clicking appears not to affect the K3 operation (port uses Com5).>>>> I use my K3 on FT8 and for eme (JT65 or Q65), so very important the>> computer I/F works correctly. B version uses direct USB/USB interface>> so might not be an issue.>>>> 73, Ed - KL7UW> ______________________________________________________________> Elecraft mailing list> Home: http://mailman.qth.net/mailman/listinfo/elecraft> Help: http://mailman.qth.net/mmfaq.htm> Post: mailto:Elecraft at mailman.qth.net>> This list hosted by: http://www.qsl.net> Please help support this email list: http://www.qsl.net/donate.html> Message delivered to rick.nk7i at gmail.com ______________________________________________________________Elecraft mailing listHome: http://mailman.qth.net/mailman/listinfo/elecraftHelp: http://mailman.qth.net/mmfaq.htmPost: mailto:Elecraft at mailman.qth.netThis list hosted by: http://www.qsl.netPlease help support this email list: http://www.qsl.net/donate.htmlMessage delivered to k9gs at gjschwartz.com