[Elecraft] [KX3] Oppopsite Sideband Null question - Redux

[Barry]

Mark,
     Where did you find the utility? I just search the web and the 
Elecraft site for the utility, but it never showed up.

73,
Barry
K3NDM

------ Original Message ------
From: "Mark Forsyth" <vk3zmf at outlook.com>
To: "Grant Youngman" <ghyoungman at gmail.com>
Cc: "Elecraft Refl" <Elecraft at mailman.qth.net>
Sent: 6/13/2020 12:17:44 AM
Subject: Re: [Elecraft] [KX3] Oppopsite Sideband Null question - Redux

>Hi,
>Elecraft have a handy little utility called RxSbNull.exe which does the whole process. All you need is an up to date KX3, an up to date XG3, a Windows computer and the utility. It works like a charm. Turn the radio volume down before you start it though otherwise it’ll annoy the hell out of you.
>
>Cheers
>Mark Forsyth
>http://jandmf.com
>VK3KW
>
>>  On 12 Jun 2020, at 11:36 pm, Grant Youngman <ghyoungman at gmail.com> wrote:
>>
>>  Elecraft Tech Support seems (understandably) a bit slow to respond at this point.   This is a repeat of a question I asked a few days ago.  Maybe someone else will see it and have some insight (?).
>>
>>  I have redone the opposite sideband null procedure in my KX3 (#8342) with KXFL3 filter board, using both the 2013 per-band null procedure, and the 2015 KXFL3 installation/calibration instructions.  The procedures are essentially the same, with a minor difference in RIT setting, and the fact that the KXFL3 installation manual calls this out only on 20M rather than on each band individually.
>>
>>  With my XG3 as a signal source,  I get an excellent opposite sideband null using either FL1 or FL2 bandwidth settings on all bands.  With narrow bandwidth and FL3 switched in, the null is very broad and shallow, and the opposite sideband is reduced only on the order of 10dB (+/-) rather than the very deep nulls (60+ dB) obtainable with FL1/FL2.  As a result, the opposite sideband remains clearly audible when tuning across a signal — say CW at 500 Hz bandwidth, etc.
>>
>>  If anyone else out there has done either of these procedures, did you get as deep a null with FL3 as with FL1/FL2?  I’m trying to determine if this is normal, or if there's an issue in the radio, possibly with my KXFL3 board.
>>
>>  Thanks … Grant NQ5T
>>  ______________________________________________________________
>>  Elecraft mailing list
>>  Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>  Help: http://mailman.qth.net/mmfaq.htm
>>  Post: mailto:Elecraft at mailman.qth.net
>>
>>  This list hosted by: http://www.qsl.net
>>  Please help support this email list: http://www.qsl.net/donate.html
>>  Message delivered to vk3zmf at outlook.com
>______________________________________________________________
>Elecraft mailing list
>Home: http://mailman.qth.net/mailman/listinfo/elecraft
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:Elecraft at mailman.qth.net
>
>This list hosted by: http://www.qsl.net
>Please help support this email list: http://www.qsl.net/donate.html
>Message delivered to barrylazar2 at gmail.com


-- 
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus