[Elecraft] Question on frequency when in fine/medium/coarse

[Bill Weaver]

The undisplayed digits are used, i.e. the freq does not shift to the displayed 100Hz. In my example the freq (while listening to a CW QSO) did not shift but stayed at 7.02647 Khz.   
  

  
73,
  
Bill WE5P
  
  
  

  
  
  
  
  
>   
> On Oct 17, 2019 at 08:59, Bob Novas  <bob.novas at verizon.net>  wrote:
>   
>         
>   
>
>  But, the question is - are the undisplayed digits retained but not used, or are they actually utilized in determining the frequency?    I’ve been setting my readout to xxxx.x00 before switching to Coarse, on the fea that the undisplayed digits actually are used in determining the Rx/Tx frequency, but there’s nowhere that says one way or the other that I can find.    Bob - W3DK
>
>   
>
>     
>
>   
>
>  From:    Bill Weaver [mailto:weaverwf at usermail.com]
>   Sent:  Thursday, October 17, 2019 8:34 AM
>   To:  Bill Weaver; Bob Novas; Bob Novas via Elecraft
>   Subject:  Re: [Elecraft] Question on frequency when in fine/medium/coarse
>
>   
>
>   
>
>   
>   
>   
>
> Sri, when selecting coarse to 7.0264 not 7.02644. Fat fingers
>
>   
>   
>   
>
> 73,
>
>   
>   
>   
>
> Bill WE5P
>   
>
>
>   
>   
>   
>   
>   
> >   
> >   
> >
> > On Oct 17, 2019 at 08:31, Bill Weaver  <weaverwf at usermail.com>  wrote:
> >
> >   
> >   
> >   
> >   
> >   
> >   
> >  Bob,  
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >  I just tested it. It looks like the undisplayed digits are retained. My example 7.02647. Select coarse 7.02644 tune around and return to 7.0264 and select medium returns to 7.02647.  
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >  73,  
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >  Bill WE5P  
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   
> >   >   
> >   
> >   >  On Oct 17, 2019 at 08:23, Bob Novas via Elecraft wrote:  
> >   
> >   >   
> >   
> >   >   
> >   
> >   >  When the K3s is in Coarse tuning mode, showing 100 Hz steps, are the 10 Hz and 1 Hz settings retained from wherever they were, or are they jammed to 0's? In other words, if the dial reads 7010.1, is the K3s running on the frequency 7010.100 or possibly 7010.1?? where the ?? are whatever happened to be dialed in before going to Coarse tuning? Thanks, Bob Novas - W3DK ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft at mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to weaverwf at usermailcom  
> >   
> >   >   
> >   
> >   
> >   
> >  ______________________________________________________________  
> >   
> >  Elecraft mailing list  
> >   
> >  Home: http://mailman.qth.net/mailman/listinfo/elecraft  
> >   
> >  Help: http://mailman.qth.net/mmfaq.htm  
> >   
> >  Post: mailto:Elecraft at mailman.qth.net  
> >   
> >   
> >   
> >  This list hosted by: http://www.qsl.net  
> >   
> >  Please help support this email list: http://www.qsl.net/donate.html  
> >   
> >  Message delivered to weaverwf at usermail.com  
> >   
> >
> >   
> >
> >   
>   
>   
>   
>