[Elecraft] Sending AFSK RTTY--FIXED

Thu Mar 21 22:04:33 EDT 2019

Pete will be able to share the CAT connection when he gets Win4K3Suite.

Mark, WB9CIF

-----Original Message-----
From: elecraft-bounces at mailman.qth.net <elecraft-bounces at mailman.qth.net> On Behalf Of rocketnj at gmail.com
Sent: Thursday, March 21, 2019 23:27
To: 'Peter Dougherty' <lists at w2irt.net>; 'Joe Subich, W4TV' <lists at subich.com>; elecraft at mailman.qth.net
Subject: Re: [Elecraft] Sending AFSK RTTY--FIXED

Pete,

YouCAN share the CAT connection from the K3S USB via a program called VSPE. Works very well.
Give me a call tomorrow to discuss.

Dave wo2x

-----Original Message-----
From: elecraft-bounces at mailman.qth.net <elecraft-bounces at mailman.qth.net> On Behalf Of Peter Dougherty
Sent: Thursday, March 21, 2019 7:00 PM
To: 'Joe Subich, W4TV' <lists at subich.com>; elecraft at mailman.qth.net
Subject: Re: [Elecraft] Sending AFSK RTTY--FIXED

Yes, you're right, and I will miss the ability to have multiple CAT connections...that's a biggie and the ability to mute the mic on .wav playback as well. I should have said that I have (almost) all the functionality that I had before for the features that I use. At this point, I'm trying to simplify things for the next couple of months, get things working reliably, then introduce an SDRPlay, Skimmer, and Win4K3 after Dayton. 

I do miss the Winkeyer's speed control knob, but I can get used to just using N1MM PageUp/Dn keyboard commands or the K3s's front panel control knob. I had a great run with the MK and MK-II over the years and yeah, there are a few things I'll miss, for sure, but the reduced complexity--both physical and software/PC related, and reduced potential for RF ingress are substantial positives as well. 

 - pjd

-----Original Message-----
From: elecraft-bounces at mailman.qth.net <elecraft-bounces at mailman.qth.net> On Behalf Of Joe Subich, W4TV
Sent: Thursday, March 21, 2019 3:52 PM
To: elecraft at mailman.qth.net
Subject: Re: [Elecraft] Sending AFSK RTTY--FIXED

On 2019-03-21 1:52 PM, Peter Dougherty wrote:
 > Again, a big thank you to everybody who lent a hand to this. One final  > question, does the USB audio connection from the K3s separate out the  > main and sub receiver audio in the same manner as using a physical  > audio breakout cable two and 3.5mm plugs?

Yes, the K3/KIO3B or K3S USB Audio CODEC behaves exactly like the K3 with analog Line In/Line Out.  The USB Audio CODEC is essentially "grafted on" to the Line In/Line Out.  In fact "Speaker (USB AUDIO CODEC)" is connected in parallel with the analog Line Out jack.

Please refer to the K3S Owners Manual and the K3S schematic package on-line.

> I seem to have all the functionality I had previously with the
 > MicroKeyer-II in line

Not by a long shot ... you no longer have a hardware based FSK, a K1EL WinKey keyer, support for multiple CAT connections (for syncing an external SDR panadapter), the ability to mute the microphone when playing an SSB voice file, access to dedicated CI-V and/or SteppIR control channel, etc.  While you may not have used all those features you certainly do not have the same functionality as you had with the microKEYER II.

73,

    ... Joe, W4TV

On 2019-03-21 1:52 PM, Peter Dougherty wrote:
> Hi all,
> Just a quick note to thank everybody here for their suggestions and help. 
> There were some things in the K3s that needed to be changed, but that 
> still left some serious issues that were definitely related to DX Labs 
> WinWarbler.
>
> DX Labs works by storing app settings in the registry, and the 
> registry settings for all related apps are stored in a “workspace.”
> Somehow the settings for WinWarbler had gotten corrupted. On a whim, I 
> restored an old known-good workspace, changed the parameters to the 
> new hardware configuration and after a couple of bumpy starts, everything worked fine.
> I saved a new workspace with these settings, and then I went back to 
> the original profile, and it remained screwed up. Once again I shut 
> everything down, loaded the new profile that I’d just created and it’s 
> all good. The bad profile has now been deleted off the system and all 
> is once again right.
>
> I would definitely like to thank Barry, K3NDM for helping me out 
> one-on-one, ironing out the needed K3s settings, and getting RTTY 
> working in FLDIGI and N1MM (proving this was a DX Labs problem).
>
> FOUR DAYS to get this done, but at least now, with very limited 
> testing, I seem to have all the functionality I had previously with 
> the MicroKeyer-II in line—but without the extra cabling, risk of RF 
> ingress, and multiple virtual COM ports.
>
> Again, a big thank you to everybody who lent a hand to this. One final 
> question, does the USB audio connection from the K3s separate out the 
> main and sub receiver audio in the same manner as using a physical 
> audio breakout cable two and 3.5mm plugs? I would like to have a 
> second instance of MMTTY set up to receive the sub RX audio, with the 
> primary using only the main VFO. I used to be able to accomplish this 
> using left- and right-channels in the MMTTY setup, but that doesn’t 
> seem to work using USB. Not a major issue now that FT8 Dxpedition Mode 
> seems to be all the rage, but I would still like to have this functionality if possible.
>
>
>
> - pjd
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html