[Elecraft] Troublesome Macro #1 (First in a series)

[Nr4c]

Did you try without the “delays”?

Is it so hard to start wsjt-x and select the 6M frequency in the drop- down box, and then adjust the P3? 

And with the full spectrogram from wsjt-x , I don’t pay much attention to the O3. 

Sent from my iPhone
...nr4c. bill


> On Jul 2, 2018, at 8:41 PM, Byron Peebles <nz3o.us at gmail.com> wrote:
> 
> I am having trouble with the following Macro on a K3S and P3/SVGA.
> 
> BN10;DE500;MD6;DE100;FA00050313000;DE100;#CTF+00050315000;DE100;#SPN000043;DE100;
> 
> The delays are just there to slow things down, right?  No impact otherwise.
> 
> What happens is the Macro executes, but when it completes, the P3/SVGA switches the Center Frequency back to the previous band and the band the radio is on is correct but the SVGA display differs from the P3 itself by quite a bit.  For specifics, I test the Macro by switching to 28MHz band.  After execution, the P3 shows the 28MHz center frequency but the SVGA shows 74Mhz, or thereabouts.  - If I change the SPN, the center frequency varies. Suspicious.
> 
> What I am trying to accomplish is this:
> 
> Change bands(6m), Set Mode(Data), Set VFO-A Frequency (50313), Set P3 Center (50315) and P3 Span (4.3)
> 
> The idea is to have the audio bandwidth of FT-8 on the SVGA display (in this example).
> 
> What obvious mistake am I missing and forgetting?  Thank you.
> 
> 73, Byron
> 
> Note the results are the same whether in a Macro button or some the test command line. The results are fine when the command is broken up.  I do know about delays in command execution, especially band changes, and it does work better when you are already on the band.
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to nr4c at widomaker.comI am having trouble with the following Macro on a K3S and P3/SVGA.
> 
> BN10;DE500;MD6;DE100;FA00050313000;DE100;#CTF+00050315000;DE100;#SPN000043;DE100;
> 
> The delays are just there to slow things down, right?  No impact otherwise.
> 
> What happens is the Macro executes, but when it completes, the P3/SVGA switches the Center Frequency back to the previous band and the band the radio is on is correct but the SVGA display differs from the P3 itself by quite a bit.  For specifics, I test the Macro by switching to 28MHz band.  After execution, the P3 shows the 28MHz center frequency but the SVGA shows 74Mhz, or thereabouts.  - If I change the SPN, the center frequency varies. Suspicious.
> 
> What I am trying to accomplish is this:
> 
> Change bands(6m), Set Mode(Data), Set VFO-A Frequency (50313), Set P3 Center (50315) and P3 Span (4.3)
> 
> The idea is to have the audio bandwidth of FT-8 on the SVGA display (in this example).
> 
> What obvious mistake am I missing and forgetting?  Thank you.
> 
> 73, Byron
> 
> Note the results are the same whether in a Macro button or some the test command line. The results are fine when the command is broken up.  I do know about delays in command execution, especially band changes, and it does work better when you are already on the band.
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to nr4c at widomaker.com