[Elecraft] FS: Elecraft K3/100, power supply, cables...

[Clay Autery]

SOLD

______________________
Clay Autery, KY5G
(318) 518-1389

On 01-Aug-18 10:53, Clay Autery wrote:
> I am re-listing the following for, and with the authority of Carl 
> Beck, W5BEK:
>
>
> *** Elecraft K3 Transceiver (Serial #5765) as specified below ***
>
> PLUS: Adding the PowerWerx SS-30DV power supply to the deal!!
> PLUS: 2 each UHF to UHF jumpers (Belden 8214 cable stock 11 AWG)) (K3 
> to amp and amp to tuner)
>
> Here are the details on the radio:
>
> + K3/100 - K3 100W Transceiver Modular Kit
> + KAT3 - K3 ATU Modular Kit
> + KTCX03-1 - K3 TXCO  1ppm f/w correction to 0.5 ppm
> + KFL3A-2.8K - 2.8 kHz 8 pole roofing filter
> + KFL3A-2.1K - 2.1 kHz 8 pole roofing filter
> + KFL3A-1.0K - 1.0 kHz 8 pole roofing filter
> + KFL3A-400 - 400 Hz 8 pole roofing filter
> + KUSB - Universal Serial Bus Adapter (RS-232 to USB)
> + MH-2 Microphone for K3
> + K3 Power supply cable - This appears to be a heavier gauge wire than 
> the OE cable.  Power Pole x formed/tinned terminal hooks.
>
> ++ KSYN3AUPG - KSYN3A Synthesizer Upgrade Kit for K3
> ++ KXV3B - RX Ant., 2nd Pre-Amp, IF Out and Xverter Interface 
> upgrade.  Adds 2nd preamp for 12,10,6 M
>
> This radio was housed in the central air-conditioned portion of a 
> no-smoking home.  It has never been taken to the field and is in 
> excellent, lightly used condition.
>
> After completion of this "K" version assembly, the unit was 
> subsequently submitted to Elecraft for bench testing and was fully 
> evaluated and calibrated and found to have "met or exceeded all 
> published specs".
>
> Between 12 July 2018 and the date of this "For Sale" post, the 
> following maintenance/checks were performed by Clay Autery, KY5G:
>
> 1) Upgraded to latest firmware:  Version 5.64
> 2) Thorough internal and external cleaning/detail.
> 3) Checked for any "loose" fasteners; none found.
> 3) Full replacement of Main and Sub-RX AF and RF knobs with current
> production design
> 4) Brand new LCD bezel
> 5) Calibrations performed:
>      a) Transmitter Gain: 5W and 50W  (will do Milliwatt TX Gain 
> Calibration if needed/on request)
>      b)  Reference Oscillator: per method #2, Zero-Beat @ 20 MHz. Dead 
> on; no adjustment required!!
>      c)  Front Panel Temperature Sensor: set per manual procedure
>      d)  PA Temperature Sensor:  set per manual procedure
>      e)  S-Meter and RF GAIN Control:  set per manual procedure
> 6) Function check on all bands/SSB/AM/CW
>
> This radio is ready to go!
>
> High resolution photographs can be viewed here ----> 
> http://www.montac.com/images/k3_5765/
>
> Original cost for this configuration: $3,355.45  Cost for closest 
> current configuration:  $4,229.50
>
> **** Price:  $2,300.00 plus shipping and insurance.****
>
> Payment via certified funds, check, PayPal.  Personal check will be 
> held until clearing.  PayPal is price PLUS PP fees. Will be shipped in 
> an Elecraft Factory box/packaging.
>
> Inquiries may be made to me directly, off-list, or by phone.
>
> 73,
>