[Elecraft] SPE 1K-FA Amp hookup and ALC Question

[M. George]

I have an SPE 2K-FA I'm using with a K3S... very happy with it.  I made a
verbose YouTube <https://www.youtube.com/watch?v=Ku8Gyl0amRY> video early
on after I received the amp which gets into the details of making the
interface cable.  (these days guys can pass the Extra Class exam but they
can't make a simple interface cable to an amplifier... ;) )  All of the
details would apply to the 1K-FA.

As others have stated, don't use ALC on the K3 to control the output of
your SPE amp, however it is viable as a safety measure to let the amp drop
the K3 output if it's software deems necessary. (despite what you will read
in the SPE manual where it says just crank the power output on your exciter
all the way up and let the amp control the output via ALC)  I get into the
details around this in the video several times.  You can fast forward and
find the areas you are interested in related to the cable interface to the
K3.

Here is the link to the video again... I hope you find something helpful...
related to your 1K-FA.

https://www.youtube.com/watch?v=Ku8Gyl0amRY

Max NG7M





On Mon, Oct 9, 2017 at 4:05 PM, Bob McGraw K4TAX <rmcgraw at blomand.net>
wrote:

> I agree with Jim, K9YC on the ALC points.
>
> With older radios, namely tube types which required the exciter PA to be
> loaded correctly to be linear, this power level would overdrive many
> amplifiers.   Hence ALC from the amp to the transceiver/transmitter was
> required to control the drive power.
>
> Today's radios have much more accurate power control methods. These
> methods are far superior to those found in most amps.   Most solid state
> amps have adequate protection with regard to overdrive, again ALC from the
> amp to the radio is not needed. And as Jim indicated, if one chooses to use
> ALC from the amp to the transceiver and it is not properly adjusted, one
> can expect signal report issues and unfriendly neighbors on the radio
> spectrum.
>
> 73
>
> Bob, K4TAX
>
>
> On 10/9/2017 4:50 PM, Jim Brown wrote:
>
>> On 10/9/2017 12:48 PM, Clay Autery wrote:
>>
>>> I'm being given an SPE 1K-FA for use with my fully current K3s.
>>>
>>> I'm being told that the K3s and SPE don't play well together using "ALC".
>>> A conflicting report is telling me that Elecraft addressed the ALC issue.
>>>
>>
>> I owned one of these amps for a few months, having bought it to get more
>> power on 6M than the KPA500 did.  I didn't like it much. You probably know
>> that ALC should NEVER be used between a rig and an amp to set the output
>> power. That's a recipe for creating harmonics, clicks, and splatter. The
>> right way to do it is to reduce drive power. If you're going to use ALC at
>> all, set output power by reducing drive and use ALC ONLY to protect the amp
>> when something goes wrong with an antenna (like the operator connecting the
>> wrong one). :)
>>
>> 73. Jim K9YC
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to rmcgraw at blomand.net
>>
>
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to m.matthew.george at gmail.com
>



-- 
M. George