[Elecraft] KPA runaway issue

[W1GO (Joe)]

Guy,

Yes.  I did that.  I meant to say TX calibration below … I said gain calibration.

Thanks.

Joe

> On May 6, 2017, at 1:07 PM, Guy Olinger K2AV <k2av.guy at gmail.com> wrote:
> 
> Run the 5 and 50 watt TX power calibration on the K3.  It's in the K3 utility program. 
> 
> 73, Guy K2AV 
> 
> On Sat, May 6, 2017 at 12:51 PM W1GO (Joe) <w1go at icloud.com <mailto:w1go at icloud.com>> wrote:
> 
> Elecraft faithful,
> 
> Any guidance with trouble shooting a KPA500 / K3 issue would be helpful.
> 
> Problem: KPA500, primarily in SSB, “redlines” (600W+ LED) after a few seconds of transmission / speech.  This seems to be independent of band.  With the KPA in standby, the K3 output power holds rock steady as indicated in the KPA.
> 
> Conditions:
> -  Only about 20W of drive in SSB can result in the “redlining”  … To eliminate the redlining, I have to turn drive down to about 18W. … about 20W in CW provides about 500W fairly solid.
> -  The K3 is powered by a 70A supply that does not sag much upon K3 keydown (14V to ~13.7V indicated on K3)
> -  KPA is powered off 240 … I tried two different KPA transformer taps as I noticed with yellow tap the supply voltage right about 60V and occasionally a little below on key down.  Supply voltage stays well above 60V with red tap but same “redlining” of the KPA.
> -  Have tried various mic gain compression settings using dynamic mikes.  Without amp in-line I do fine with gain 30, compression 20 (10db).  I’ve gone as low as gain 15 / compression 15 (~5db) with no impact.
> - I’ve tried various TXG VCE rating from -1.5 to 1.5 … no impact.
> -  ALC on … ext ALC off …. varied these to see if there would be an impact.  None.
> -  SWR (to different antennas) is <1.7 w/o KAT500 and <1.3 w/ KAT500
> 
> 
> What I’ve tried / done:
> -  Gain / compression changes as above
> -  Checked K3 supply voltage and no significant voltage drop on key down
> -  Changed power supply to a 35A powering K3 with no change
> -  Varied KPA transformer taps to ensure supply above 60V
> -  Changed coax between K3 and KPA and KPA and KAT500
> -  Tried with two different antennas / coax runs and had same result
> -  Varied TXG VCE from -1.5 to 1.5
> -  Performed gain calibration on K3 (TX calibration) 
> 
> 
> 
> I’ve had the KPA for about 9 months but primarily operated CW so not sure if this is a recent occurrence.  Any other suggestions would be appreciated.
> 
> Many thanks, all, and have a wonderful weekend.
> 
> 
> 
> Kindest regards,
> 
> Joe
> W1GO
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft <http://mailman.qth.net/mailman/listinfo/elecraft>
> Help: http://mailman.qth.net/mmfaq.htm <http://mailman.qth.net/mmfaq.htm>
> Post: mailto:Elecraft at mailman.qth.net <mailto:Elecraft at mailman.qth.net>
> 
> This list hosted by: http://www.qsl.net <http://www.qsl.net/>
> Please help support this email list: http://www.qsl.net/donate.html <http://www.qsl.net/donate.html>
> Message delivered to k2av.guy at gmail.com <mailto:k2av.guy at gmail.com>
> -- 
> Sent via Gmail Mobile on my iPhone