[Elecraft] KX2/KX3 menu pauses when passing ATU.DATA with KXPA100 attached

[Don Wilhelm]

Erik,

I cannot confirm or deny, but the 2 sets of ATU.DATA should be "N/A" or 
"--" when the KXPA100 is enabled.

Think about it a bit - the 2 data sets only pertain to the internal ATU 
in the KX2/KX3.  When the KXPA100 is enabled, that internal tuner is 
bypassed because any ATU must be on the output of the KXPA100.

The 2 sets of ATU.DATA is for field and home operation of the base 
KX2/KX3, not for the KXAT100.

73,
Don W3FPR

On 7/6/2017 9:23 AM, Erik Tkal wrote:
> Any confirmation on this issue?
> 
>    Thanks and 73,
>    Erik Tkal  -  W1QED
> 
> 
> 
> On Jun 18, 2017, at 13:00, E T <etksubs at gmail.com> wrote:
> 
> BTW, the KX2 with 2.77 behaves exactly the same way when scrolling past the N/A with the KXPA100 enabled.
> 
>    Thanks and 73,
>    Erik Tkal  -  W1QED
> 
> On Jun 18, 2017, at 10:34 AM, E T <etksubs at gmail.com <mailto:etksubs at gmail.com>> wrote:
> 
> Hi Wayne,
> 
> There is one major quirk with the new ATU.DATA menu item on the KX3.  When using the KXPA100 the menu item shows up with the label N/A and value "--".  And then when you scroll up or down to the next menu item it takes up to a second to show the correct label.  Even when you are scrolling fast through the items and go past that one the N/A appears and persists as you scroll.  All the other transitions are immediate except this one.  Shouldn't the label still show as ATU.DATA and have the value show "--" or "N/A"?  E.g. like 2M/4M shows as "not inSt".
> 
> I'm going to update my KX2 to the beta that also has this and see if it also shows the same quirk.
> 
>    Thanks and 73,
>    Erik Tkal  -  W1QED
> 
> 
> On Apr 27, 2017, at 11:38 PM, Wayne Burdick <n6kr at elecraft.com <mailto:n6kr at elecraft.com>> wrote:
> 
> Hi all,
> 
> Rev. 2.70 KX3 firmware unintentionally reduced the max AF gain setting for both speaker and headphones. (We improved the granularity of the AF GAIN control at the low end but didn’t get around to scaling the high end back up to the original level.)
> 
> If you were affected by this and would like to try the field test release (rev. 2.76), please email me directly.
> 
> This rev also includes the new “ATU DATA” menu entry, which gives you two full sets of per-band ATU data for use when running the KX3 “barefoot” (without the KXPA100/KXAT100). Typically one set would be used at home, the other in the field. If you do a lot of outings, this can save you the trouble of re-matching all of your antennas when you get home. Another use for this is with two different antennas for a given band.
> 
> 73,
> Wayne
> N6KR
> 
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft <http://mailman.qth.net/mailman/listinfo/elecraft>
> Help: http://mailman.qth.net/mmfaq.htm <http://mailman.qth.net/mmfaq.htm>
> Post: mailto:Elecraft at mailman.qth.net <mailto:Elecraft at mailman.qth.net>
> 
> This list hosted by: http://www.qsl.net <http://www.qsl.net/>
> Please help support this email list: http://www.qsl.net/donate.html <http://www.qsl.net/donate.html>
> Message delivered to etksubs at gmail.com <mailto:etksubs at gmail.com>
> 
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to donwilh at embarqmail.com
>