[Elecraft] Now that the K-Pod is shipping, we could use your help with useful macros

[brian]

Are these 16 macros in addition to above those previously available in 
firmware to be assigned to various K3 buttons?

73 de Brian/K3KO



On 7/8/2016 16:07 PM, Dick Dievendorff wrote:
> The most recent K3 Utility (1.16.26.5) stores 16 command macros in the K3.
> You can install it now from a link at the bottom of:
> http://www.elecraft.com/K3/k3_software.htm
>
> Command macros 1-8 correspond to K-Pod buttons F1-F8 Hold, Command macros
> 9-16 correspond to K-Pod buttons F1-F8 tap.
>
> 73 de Dick, K6KR
>
>
> -----Original Message-----
> From: Elecraft [mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Matt
> Murphy
> Sent: Friday, July 8, 2016 08:50
> To: Roger Marrotte <marrotte at verizon.net>
> Cc: Elecraft Reflector <Elecraft at mailman.qth.net>
> Subject: Re: [Elecraft] Now that the K-Pod is shipping, we could use your
> help with useful macros
>
> Is there a specification of how the macros work with the knobs? I have not
> yet ordered a K-Pod, but would love to write some useful macros (especially
> for the knobs). Perhaps I could test the macros using the K3 terminal in the
> meantime but it would be great to know how the knobs are configured to
> trigger macros first.
>
> Advice appreciated.
>
> 73,
> Matt NQ6N
>
> On Fri, Jul 8, 2016 at 10:42 AM, Roger Marrotte <marrotte at verizon.net>
> wrote:
>
>> Yes it does.  It comes with two 6.8 ohm resistors. One 1/8 watt leaded
>> resistor and one 1/10 watt smd resistor.  I did the mod with the smd
>> resistor.  It's a small resistor about the size of a large fruit fly
>> and it goes kind of in a tight place, especially for a left hander.  I
>> got it in and it works so I'm happy but if I had to do it again I'd
>> probably used the leaded resistor.  I've done some smd work before.
>>
>> Roger, W1EM
>>
>> -----Original Message-----
>> From: Elecraft [mailto:elecraft-bounces at mailman.qth.net] On Behalf Of
>> Terry Schieler
>> Sent: Friday, July 08, 2016 10:56 AM
>> To: 'Wayne Burdick' <n6kr at elecraft.com>; 'Elecraft Reflector'
>> <elecraft at mailman.qth.net>
>> Subject: Re: [Elecraft] Now that the K-Pod is shipping, we could use
>> your help with useful macros
>>
>> Looks like my K-Pod should arrive tomorrow.  Does it come with the DC
>> power modification resistors and mod instructions or do I need to order
> those?
>>
>> 73,
>>
>> Terry, W0FM
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net Please help support this email
>> list: http://www.qsl.net/donate.html Message delivered to
>> matt at nq6n.com
>>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html Message
> delivered to dick at elecraft.com
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to alsopb at comcast.net
>