[Elecraft] K2 build from purgatory!

[James Bennett]

Since I no longer have a K2, I’m only taking a WAG here, but would this not be a good candidate for Chip Quick? I used it to pull an SMD IC off a board a few weeks ago and it absolutely works great….

73, Jim / W6JHB


> On   Tuesday, Apr 12, 2016, at  Tuesday, 1:24 PM, Dale Putnam <daleputnam at hotmail.com> wrote:
> 
> I've had good luck removing that relay with a hot air smd rework station.. one must be aware of how much air.. and what temp.. but heat applied to the other side of the board, just enough to flow the solder.. on one pin at a time.. to lift the relay a smidge.. then move to the next pin.. .. OR enough heat to simply lift the relay.. either way works.. 
> and relay removal by pieces works too. 
> 
> Have a great day,
> --... ...-- Dale - WC7S in Wy
> 
> 
> ________________________________________
> From: Elecraft <elecraft-bounces at mailman.qth.net> on behalf of Don Wilhelm <w3fpr at embarqmail.com>
> Sent: Tuesday, April 12, 2016 1:49 PM
> To: lstavenhagen; elecraft at mailman.qth.net
> Subject: Re: [Elecraft] K2 build from purgatory!
> 
> LS,
> 
> I would try pliers first, but watch the process as you apply pressure.
> It may assist if you damage the case more with your soldering iron (melt
> more of the plastic) until you can get an Exacto knife edge into it to
> help with the process.
> As I said, use any tool that works - just be careful not to damage other
> nearby components.
> 
> 73,
> Don W3FPR
> 
> On 4/12/2016 3:11 PM, lstavenhagen wrote:
>> Ah yes, thanks for that reminder. If it comes to that, is there a good way to
>> smush a latching relay body without dangerously ripping the pins out of the
>> board? I worry that crushing it with say a pair of pliers could stress the
>> through-holes in the board. Or is it just not that strong?
>> 
>> Thanks,
>> LS
>> W5QD
>> 
>> 
>> 
>> --
>> View this message in context: http://elecraft.365791.n2.nabble.com/K2-build-from-purgatory-tp7616239p7616253.html
>> Sent from the Elecraft mailing list archive at Nabble.com.
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to w3fpr at embarqmail.com
>> 
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to daleputnam at hotmail.com
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to w6jhb at me.com