[Elecraft] Using external sound card for digital modes

[Walter Underwood]

You don’t want the KX3 in SSB (USB) for these modes. If you do that, you need to turn off TX EQ, compression, and RX EQ every time you go digital. Then turn it all back on for voice.

DATA A exists primarily as a separate config set for USB that takes care of that for you.

wunder
K6WRU
CM87wj
http://observer.wunderwood.org/

On Jan 29, 2015, at 9:17 AM, David Ahrendts <davidahrendts at me.com> wrote:

> Also, part of the magic of using FLDigi and a SignaLink card is that the software does all of the work by design. The KX3 remains in SSB mode for PSK or RTTY, so it becomes a quick cable swap to plug in digital or plug in a microphone.
> 
>> On Jan 29, 2015, at 8:40 AM, David Ahrendts <davidahrendts at me.com> wrote:
>> 
>> My friend, I had the same type of problem in bringing the KX3 up to speed for digital. The rig would begin wildly scanning when connected to an Mic sound card. My solution was to use my old Signalink sound card instead with a home brew cable. Does a very nice job. In trouble shooting the iMic (which I never got to work), someone mentioned checking the mini-plug type. Remember the KX3 microphone plug is a tip-ring-sleeve plug (TRS). Presumably a mono or stereo plug would cause unexpected things to happen.
>> My two cents for you.
>> 
>> David Ahrendts, KC0XT, LA 
>> 
>>> On Jan 29, 2015, at 8:32 AM, RB3 <hes.not.here at gmail.com <mailto:hes.not.here at gmail.com>> wrote:
>>> 
>>> Good morning!
>>> 
>>> I've only had my KX3 for a month, but I've enjoyed it so far. Recently, I
>>> have been trying to operate digital modes (RTTY and PSK31) using my SB
>>> Audigy 2 NX external sound card and several different programs (fldigi,
>>> KComm, HRD, and a few others). I am using the KX3USB for control and the
>>> KX3-PCKT cables (Red, Green, and I/Q) for input/output/analyzer. Every time
>>> I connect the MIC input to the sound card output, the rig keys down until I
>>> unplug the red cable from the input.
>>> 
>>> I've tried using different selections in the programs for PTT (serial, VOX,
>>> software), but nothing seems to work. I am aware of other options out
>>> there, such as the RigBlaster and SignaLink USB, but I was hoping to be
>>> able to use the equipment I already have.
>>> 
>>> Any suggestions would be most welcome.
>>> 
>>> 73,
>>> Sonny
>>> KC3DNN
>>> 
>>> -- 
>>> -=((hes.not.here at gmail.com <mailto:hes.not.here at gmail.com>))=-
>>> ______________________________________________________________
>>> Elecraft mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft <http://mailman.qth.net/mailman/listinfo/elecraft>
>>> Help: http://mailman.qth.net/mmfaq.htm <http://mailman.qth.net/mmfaq.htm>
>>> Post: mailto:Elecraft at mailman.qth.net <mailto:Elecraft at mailman.qth.net>
>>> 
>>> This list hosted by: http://www.qsl.net <http://www.qsl.net/>
>>> Please help support this email list: http://www.qsl.net/donate.html <http://www.qsl.net/donate.html>
>>> Message delivered to davidahrendts at me.com <mailto:davidahrendts at me.com>
>> 
>> 
>> 
>> 
>> David Ahrendts   davidahrendts at me.com <mailto:davidahrendts at me.com>   
>> 
>> 
>> 
>> 
> 
> 
> 
> 
> David Ahrendts   davidahrendts at me.com   
> 
> 
> 
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to wunder at wunderwood.org