[Elecraft] K3 macro's to switch mic's

[Bill Conkling]

No problem, Jeff.  

This combo is just that, a start.  There are some gurus on the list that
have written macros that only require one pf# key as they do some magic and
self-modify themselves to toggle the setup.  Maybe when they finish the
discussion on one verses two mics or speakers +/- phones, one of them will
enlighten us with some real useful information.

'till then, I use the macros I sent you myself, with some mods to the TE:

Good luck.

...bill nr4c

-----Original Message-----
From: Jeff Griffin [mailto:kb2m at comcast.net] 
Sent: Wednesday, March 19, 2014 8:20 PM
To: 'Bill Conkling'
Cc: elecraft at mailman.qth.net
Subject: RE: [Elecraft] K3 macro's to switch mic's

Thanks Bill this is exactly what I was looking for, some place to start. I
was wondering if anyone else has setup any macros for mic selection.
Thanks....

73 Jeff kb2m 

-----Original Message-----
From: Bill Conkling [mailto:nr4c at widomaker.com]
Sent: Wednesday, March 19, 2014 5:44 PM
To: kb2m at comcast.net
Cc: elecraft at mailman.qth.net
Subject: RE: [Elecraft] K3 macro's to switch mic's

Jeff,

I watched this nthread for a while and saw a dozen or so responses, but
no-one bothered to help you with a macro or two.  It seems that everyone has
opinions on what mic or jack and maybe which fingefr to use to press the
"ON".

But, as for the macros, here goes.

These are old, but you can see what I have done and adjust accordingly.
Good luck!

************************************************

TO set mic to front for Hiel  HM10-Dual

Name:   -MicFP

Macro:  MG020;CP020;MN053;DN;DN;TE-03-03+00+00+03+03+00+00;SWT11;

ASSIGN TO PF1

This will set gain to 20, the compression to 20, set mic to front, adjust TX
Equalization and set range to H


To set rear for YAMAHA CM500

Name:   -MicRPl

Macro:  MG017;CP005;MN053;DN;DN;UP;TE+00+00+00+03+03+03+03+03;SWT11;

ASSIGN TO PF2

This will set gain to 17, compression to 5, set mic to rear, adjust TX
Equalization and set range to L

NOTE:'

The setting for range H or L is a toggle.  If you press the same function
key twice, it will toggle the range.  Therefore these macros leave the Main
Menu active to show the Front/Rear and Range setting.  Just press the MENY
butoon and you are ready to go.  If the range is wrong, just press keypad #1
to toggle to the other setting.

...bill

-----Original Message-----
From: elecraft-bounces at mailman.qth.net
[mailto:elecraft-bounces at mailman.qth.net] On Behalf Of kb2m at comcast.net
Sent: Wednesday, March 19, 2014 12:06 PM
To: elecraft at mailman.qth.net
Subject: [Elecraft] K3 macro's to switch mic's

Does anyone have (or know where I can get)a set of macros they would share
with me that will change a K3's mic input, along with TX eq, mic gain, comp,
etc. I'm setting my K3 up for the first time for other then DX use with the
CM500 headset. I'm going to be also using an 8 pin Kenwood MC-50. My K3 was
up to now for DX only use, but as I'm downsizing I would now like to it use
for other types of operating, and would like to use macros for the first
time to switch between the two mic's. Thanks in advance for any useful
information...  

73 Jeff KB2M


______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message
delivered to nr4c at widomaker.com