[Elecraft] K3 won't unkey properly: Rear panel PTT

[David Cole]

Interestingly enough I have something like that happen now and then as
well...

I am driving the K3 directly with a serial port from my computer, and in
DATA A mode, so far only when in DATA A.  I operate 90% in DATA A so
take that last one with a grain of salt...  Although it has never
happened in CW mode.

Once the problem has been triggered, if I tap the XMIT button and it
drops out of transmit.  Next time, I'll try a different button...  

I am using no interface...
-- 
Thanks and 73's,
For equipment, and software setups and reviews see:
www.nk7z.net
for MixW support see;
http://groups.yahoo.com/neo/groups/mixw/info
for Dopplergram information see:
http://groups.yahoo.com/neo/groups/dopplergram/info
for MM-SSTV see:
http://groups.yahoo.com/neo/groups/MM-SSTV/info


On Sun, 2014-07-13 at 19:01 -0700, Dan Sherwood wrote:
> I have discovered an issue with my K3, (ser 5820).
> 
> When using my Tigertronics Signalink USB device, the unit keys the rig fine,
> but when the interface unkeys, transmission ceases, but red XMIT light stays
> on and reception is muted.  Like an indeterminate state.
> 
> I did the following:
> 
> Updated firmware ­ no difference.
> 
> Unplugged Signalink rig cable to r/o a short ­ no difference.
> 
> Ran a different digital program on laptop ­ no difference.
> 
> The rig is configured to accept audio input from the line in jack on the
> rear when placed in DATA-A mode.  In SSB mode it accepts input from either
> the front panel or the rear MIC jack depeng on whether I am using a headset
> or the boom mic.  PTT is asserted through a foot switch via the front panel
> MIC jack.  This keys and UNKEYS normally.
> 
> The Signalink assertes PTT through the PTT jack on the rear panel of the K3.
> It has an internal relay acting like VOX.
> 
> When I use the signalink to key up in data mode, it works OK for a few
> cycles, then reverts to the indeterminate state.  Rig will not receive until
> I tap one of the keys mentioned below.
> 
> To rule out RF feedback issues, I keyed the signalink in SSB mode, so
> line-in not selected,  Rig keys up but no power made, (signalink audio not
> selected).  Problem persists.
> 
> Normal CW and SSB using foot switch PTT and either full or semi break in CW
> has no issues, even when driving an amp and lots of RF.
> 
> CW through FLDIGI uses CAT keyup and release.  No issues there.  PSK uses
> PTT asserted through rear panel.  Issue seems with rear panel PTT only.
> 
> Now here¹s the really strange thing:  When in this indeterminate muted
> state, if I tap band up or down, mode up or down, AFX, XIT, or RIT keys, the
> unit goes back to normal receive.  That initial tap DOES NOT perform the
> key¹s design function.  This is like a computer keyboard when a screensaver
> is running ­ the first keypress is ³swallowed² to wake up the screen, then
> subsequent keypresses work normally.  Any ideas here?
> 
> Thanks,
> 
> Dan Sherwood W6DAS
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to dave at nk7z.net