[Elecraft] CW QRQ and SPLIT

[Chester Alderman]

But if you have several hams in the round-table, you sure do need RIT because you know all hams are not going to be zero beat. Besides that, yes, ever if your one QSO partner is zero beat, you need the ability to slightly change the Rx QRQ frequency so the received tone suits your ears. Copying QRQ requires one to be able to use standard CW receiver functions. That is why I, personally, can't use my K3 for full QSK QRQ operation.
Since this issue has been on-going for several years, it most likely can not be fixed? Or it is just being ignored!

73,
Tom - W4BQF


-----Original Message-----
From: elecraft-bounces at mailman.qth.net [mailto:elecraft-bounces at mailman.qth.net] On Behalf Of John Bohnovic
Sent: Monday, February 17, 2014 11:36 AM
To: Klaus Koppendorfer
Cc: Elecraft Reflector; don at w3fpr.com
Subject: Re: [Elecraft] CW QRQ and SPLIT

Do you need the RIT mode when the other station is zero beat with your signal?

John/K4WJ
ex KN8PXG K8PXG ZF2HZ
Sent from my iPad

> On Feb 17, 2014, at 3:05 AM, Klaus Koppendorfer <KK at ccf.net> wrote:
> 
> It is sad that QRQ mode has no RIT  !!!
> Cw up from 30 to 35 WPM hast o use QRQ mode because of struggling dits 
> and dahs
> 
> Many highspeed ops VHSC EHSC has changed from k3 to FT5000 because of 
> leaking RIT with QRQ with K3
> 
> Maybe Wayne will sharpen Firmware in future for QRQ mode
> 
> If rit/split is necessary i use 2nd RX but this is not so comfortable
> 
> 73
> Oe6kyg
> Klaus
> 
> 
> -----Ursprüngliche Nachricht-----
> Von: elecraft-bounces at mailman.qth.net 
> [mailto:elecraft-bounces at mailman.qth.net] Im Auftrag von Don Wilhelm
> Gesendet: Samstag, 15. Februar 2014 22:06
> An: Jorge Diez - CX6VM; 'Elecraft Reflector'
> Betreff: Re: [Elecraft] CW QRQ and SPLIT
> 
> Jorge,
> 
> AFAIK, probably not.  The frequency must be shifted from RX to TX, and with QRQ in effect it is not possible to shift that fast.  A K3 with 'chirp' on the ham bands would not be a nice thing to hear.
> 
> 73,
> Don W3FPR
> 
>> On 2/15/2014 2:33 PM, Jorge Diez - CX6VM wrote:
>> I saw in the manual of K3 that CW QRQ is "temporarily turned OFF" 
>> with SPLIT.
>> 
>> Will be in the future any way to use it in SPLIT mode or is impossible?
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net Please help support this email 
> list: http://www.qsl.net/donate.html 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net Please help support this email 
> list: http://www.qsl.net/donate.html
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html