[Elecraft] Remote operation question

[Mitch Wolfson DJØQN]

Jim,

I highly suggest that you post this issue on the RemoteRig forum at 
http://www.remoterig.com/forum/index.php for the RemoteRig developers to 
answer. They do not read the Elecraft reflector.

73,
Mitch DJ0QN

Mitch Wolfson
DJØQN / K7DX
Neubiberger Str. 21, 85640 Putzbrunn
Skype: mitchwo - Home:+49 89 32152700 - Mobile:+49 172 8374436
Echolink: 3001 - IRLP: 5378

On 05.08.2014 17:33, Jim - KE8G wrote:
> I now see I have an error message on the remote side:
> Saved error message:
> Data Abort at 0x00043114, called by 0x000437ac
>
> Any ideas?
>
>
> ---- KE8G <ke8g at cox.net> wrote:
>> Well, the unfortunate part is that the only description I got was the radio sounded like it has a defect, nothing more and the fellow was gone.  If someone would like to setup a sked to have a listen, that would be great.  It would have to be a CW sked, as I do not have a mic.
>>
>> To update everyone commenting, I have updated the K3 firmware at the control end, so both are now at the same level.  The firmware on the RemoteRig units are identical, no changes had been made there.  The coax for the remote station is all new 400Max series fromDXEngineering, which was thoroughly tested when installed two months ago.
>>
>> I will update the RemoteRig firmware at both sites and see if that changes anything.
>>
>> Thanks all for you comments!
>> 73 de Jim - KE8G
>>
>> Sent from my iPad
>>
>>> On Aug 4, 2014, at 11:05 PM, Mike va3mw <va3mw at portcredit.net> wrote:
>>>
>>> What is the actual problem?  Defect doesn't really describe anything.
>>>
>>> I would check the readme and see if both ends need to be updated. I would suspect so.  Why not upgrade the other end just to be sure.
>>>
>>> Btw, SWR being good or bad won't really tell you much other than if your coax is presenting a 50 ohm load. It certainly won't create a bad audio situation.
>>>
>>> Mike va3mw
>>>
>>>
>>>
>>>> On Aug 4, 2014, at 10:22 PM, Jim - KE8G <ke8g at cox.net> wrote:
>>>>
>>>> Hi All,
>>>> I seem to be having a problem with my RemoteRig operation.  Everything worked perfectly when I initially set it up.  While at the remote QTH, the only change I made was to add the newest firmware to the K3.  I have not updated the firmware at the K3 control station, would this cause a problem?
>>>>
>>>> I had a person tell me the rig sounds like it has a "defect."
>>>>
>>>> Looking at things from the control end, the KAT500 & KPA500 both appear fine, no changes in SWR or power output.
>>>>
>>>> Any ideas?
>>>>
>>>> 73 de Jim - KE8G
>>>> ______________________________________________________________
>>>> Elecraft mailing list
>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>>> Help: http://mailman.qth.net/mmfaq.htm
>>>> Post: mailto:Elecraft at mailman.qth.net
>>>>
>>>> This list hosted by: http://www.qsl.net
>>>> Please help support this email list: http://www.qsl.net/donate.html
>>>> Message delivered to va3mw at portcredit.net
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to ke8g at cox.net
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to dj0qn at arrl.net
>