[Elecraft] [KX3] What features are new?

Mon Jul 15 13:25:02 EDT 2013

Quite an impressive list it is and the improvements have certainly improved
an already great radio.

73,
Fred/N0AZZ

-----Original Message-----
From: elecraft-bounces at mailman.qth.net
[mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Wayne Burdick
Sent: Monday, July 15, 2013 11:00 AM
To: KX3 at yahoogroups.com
Cc: Elecraft Reflector
Subject: Re: [Elecraft] [KX3] What features are new?

Jim, KG0PP, wrote:

> I have KX3 #249, with the original firmware UC 01.27. I upgraded to UC
1.50 yesterday. What new features should I be looking for?

Hi Jim,

That's a long list! For the benefit of you and others who may be running
older KX3 firmware, I've listed all of the most important new features and
bug fixes since rev 1.27 below.

73,
Wayne
N6KR

* IMPROVED SSB TALK POWER (CMP): Our new speech compression algorithm
provides a significant improvement in average talk power (or "punch").
ADJUSTMENT PROCEDURE:     (1) Set CMP = 0.    (2) Start with MIC gain = 0.
While speaking close-mic'ed in your "on-air" voice, increase MIC gain until
the ALC meter tickles the 5th bar.  (3) While monitoring your voice with the
KX3's voice MONintor, advance CMP to the desired level. The transmitted
signal will still be clean even at the maximum compression setting. 

* ADJUSTABLE NOISE BLANKING (NB): The level of noise blanking can now be set
using the knob above the NB switch (AF/RF-SQL). When NB is turned on, the
present setting (1-15) will be displayed on VFO B for about 3 seconds. To
select a new setting, rotate the knob before the display times out. The
setting is stored per-band. Use the lowest effective NB setting. Higher
settings may cause audible artifacts when strong signals are present.

* NOISE REDUCTION (NR) MORE EASILY ADJUSTABLE: The overall level of noise
reduction can now be set using the knob above the NR switch (AF/RF-SQL).
When NR is turned on, the present setting will be displayed on VFO B for
about 3 seconds. To select a new setting, rotate the knob before the display
times out. The setting is independent for CW and voice modes. Note: The
range of this parameter is 0-10 and corresponds to the "mix" or "M"
parameter of the RX NR menu entry; see below.

* AF GAIN SMOOTHER AT LOW END: The AF gain control now has finer granularity
at the low end. To accommodate this , the gain range is now 0-60 (was 0-40).

* INTERNAL SPEAKER BEHAVIOR IMPROVED:  (1) Fixed bug that caused audio
output mute/unmute cycling on strong signals. (2) Gain distribution changed
to reduce speaker overdrive condition related to CODEC output. (3) Audio EQ
optimized for speaker.

* NEW LED BRT MENU ENTRY: Applies to the TX, delta F, OFS, and VFO B LEDS
(not the LCD backlight). Allows brightness of these LEDs to be adjusted, but
only in the case where the LCD backlight is off. During adjustment of LED
brightness, the LCD backlight will automatically be turned off if it was on,
then turned back on when the menu is exited.

* NO SSB RX SIGNAL ATTENUATION WHEN BW < 2.4 KHz: Previously, adjusting the
bandwidth below approx. 2.4 kHz might result in up to several dB of received
signal loss. 2.4 kHz is the bandwidth at which the receiver switches from
conventional SSB demodulation to "Weaver" method to take advantage of filter
FL2 on the KXFL3 roofing filter module.

* SSB PBT CONTROLS CAN BE SET FOR WIDTH/SHIFT: The default for passband
tuning in sideband mode is LO/HI CUT (PBT functions I and II, respectively).
If the PBT SSB menu entry is instead set to NOR, then SSB mode uses the same
PBT functions as CW and DATA modes (WIDTH and SHIFT). If you alternate
frequently between LO/HI CUT and NOR (width/shift) for SSB modes, you might
want to assign the PBT SSB menu entry to a programmable function switch (PF1
or PF2). The parameter will then alternate between the two settings each
time you hold the PFx switch.

* AFSK-A SIDEBAND SELECTION NOW CORRECT: AFSK-A "normal" is LSB, reverse is
USB.

* DVR (DIGITAL VOICE RECORDER) ADDED: There are two transmit messages of up
to 15 seconds each. (A future firmware release will provide an option for 1,
2, 3, or 4 messages of 30, 15, 10, and 7.5 seconds each, respectively.)
Setup: Make sure you're in a voice mode, and that the voice MONitor level is
not zero. To record, hold REC, then tap #1 or #2. "ERASING" will appear for
4 seconds, followed by "TAP XMT". Tap XMIT, then start speaking. To end
recording, tap XMIT again. To play, tap MSG followed by #1 or #2. To
auto-repeat (e.g., a repeating CQ message), *hold* rather than tap the #1 or
#2 switch. Use MENU:MSG RPT to set the repeat interval.

* IMPROVED SSB TRANSMIT CARRIER REJECTION. 

* RIT AND XIT NO LONGER TURNED OFF UNINTENTIONALLY: In previous releases,
changing bands via direct frequency entry (FREQ ENT) or remote-control band
change commands (FA, FB, and BN) would turn off RIT and XIT. 

* TRANSVERTER FREQUENCY ENTRY FIXED:  The previous release did not handle
direct frequency entry to transverter bands correctly (e.g., 144 MHz came
out as 180 MHz). This also affected memory recall of transverter bands.

* NEW FEATURE--SWITCH MACROS: You can now program the PF1 and PF2 switches
to execute sequences of KX3 remote control , or "macros." These are created,
tested, and sent to the KX3 using KX3 Utility. The K3/KX3 Programmer's
Reference has a number of sample macros and further details.

Here's an example of what can be done with a macro. We'll call this
"SPLIT+2" (useful when setting up to call a CW DX station up 2 kHz): 

     A>B, A>B, SPLIT, move VFO B up 2 kHz, RIT/XIT off

To create this macro and assign it to PF1 or PF2, complete the steps below:

1. Run KX3 Utility. Click on the Command Tester/KX3 Macros tab.
2. Click on the Edit Macros button. This pops up the macro edit window.
3. In MACRO #1's Macro Label  field, enter the label "SPLIT+2" (without the
quotes).
4. In the Macro Commands  field, enter this text:

    SWT25;SWT25;FT1;UPB5;RT0;XT0;

(The number 5 in "UPB5" is an index into a table of step sizes. UPB5 moves
VFO B up 2 kHz, DNB5 moves it down 2 kHz, etc. There are similar commands
for VFO A. For the full list, see the "DN" (down) command in the
Programmer's Reference.)

5. Click on Send Macros 1-8 To KX3.
6. At the KX3, locate the CONFIG:MACRO x menu entry, and tap '1' if the menu
entry label is not already "MACRO 1".
7. Hold PF1 to assign PF1 to MACRO 1. Exit the menu.

>From then on, holding PF1 will flash "SPLIT+2" and execute the above
sequence. 

Up to eight macros can be sent to the KX3, but only two of them can be
assigned to PF1 or PF2 at a given time. In the MACRO x menu entry, tap '1' -
'8' to select a macro, then hold PF1 or PF2 to do the assignment.

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2012.0.2242 / Virus Database: 3204/5992 - Release Date: 07/15/13