[Elecraft] PR6 ctrl line

[Joe Subich, W4TV]

The proper splitter is available from:
   www.cablewholesale.com  p/n 10H1-27708
   www.altex.com   Philmore 70-568

Splitters from both sources are "all 15" and the same as the splitter
included with the KPA3AUX cable kit or the E980190 "Extra DB15 Y-cable"
listed with the KPA500 and K3.

73,

    ... Joe, W4TV


On 7/11/2013 6:45 PM, Cady, Fred wrote:
> Hi Joe,
> I didn't see a response to your good question, so here goes one:
> Yes you can use a standard 15-pin Y-cable splitter to split out signals you need, for example the DIGOUT1 for switching on the PR6 or to input FSK keying signals to the K3. The key thing is to make sure the cable between one side of the splitter cable to the KPA is the KPAK3AUX cable.
>
> You won't be able to use the splitter you found that is missing pin 9 as that is the BAND 2 data that the KPA uses to determine which band the K3 is on.
>
> I've had good luck with cables from www.winford.com. They also have a neat line of break-out boards for 9-pin and 15-pin cables. (I don't have anything to do with the company, but even if I did so what?)
>
> If you are going to add the KAT500 you can use a full 15-pin cable between the KAT and the KPA as long as the KPAK3AUX cable is between the K3 and the KAT.
>
> Cheers and 73,
> Fred KE7X
> "The Elecraft K3: Design, Configuration and Operation 2nd Ed."
> "The Elecraft KX3 - Going for the Summit"
> "The Elecraft K-Line - KPA500 and KAT500" (In progress)
> www.ke7x.com
> www.lulu.com (July 20% discount code is JULYBOOKS13)
>
> Fred Cady
> fcady at ieee dot org
>
>> -----Original Message-----
>> From: elecraft-bounces at mailman.qth.net [mailto:elecraft-
>> bounces at mailman.qth.net] On Behalf Of Joe K2UF
>> Sent: Tuesday, July 09, 2013 7:00 PM
>> To: elecraft at mailman.qth.net
>> Subject: [Elecraft] PR6 ctrl line
>>
>> I have an Elecraft molded cable between the K3 and KPA500 acc ports.
>> Can I
>> use a VGA 'Y' splitter to connect the PR6 ctrl  wire to the acc
>> connector on
>> the K3?  I found one on the inet that says it is wired thru except for
>> pin
>> 9.  the male end of the Elecraft acc cable has pin 9 (and others) cut
>> off.
>>
>>
>>
>> Any ideas?
>>
>>
>>
>> Joe K2UF
>>
>>
>>
>> With enough THRUST pig fly just fine.
>>
>>
>>
>>
>>
>>
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>