[Elecraft] K3/0 to K3 RemoteRig issue: NEVER MIND

[Michael]

Your U-Verse router settings are set to not respond to ping request, you could change the settings in the router to respond to ping request.

73, Michael - N8NOC

K1-4   #3046
K3/10 #6596
KX3    #1573

On Dec 19, 2013, at 9:45 AM, bwruble at gmail.com wrote:

It works. No idea why, but this morning everything is good, though I still can't ping my MD address from inside my FL network.  



Begin forwarded message:

> From: "bwruble at gmail.com" <bwruble at gmail.com>
> Date: December 19, 2013 at 9:27:04 AM EST
> To: Elecraft Reflector <elecraft at mailman.qth.net>
> Subject: Fwd: K3/0 to K3 RemoteRig issue
> 
> OK guys.  Don't waste time on this. The problem is definitely the router. 
> 
> I cannot successfully ping my remote router in Maryland (where the remote K3 is) from inside my network here in Key West. I CAN successfully ping it when I am using Verizon with my iPad.  I CAN ping anything else I try from inside the network.
> 
> Something in the way the router setup is working is preventing some kinds of data from flowing back to me.  This was not the case before AT&T's technician set up the static ip addresses.
> 
> The router is a Motorola NVG510 used by the ATT U-Verse system. On-line, I find many forum threads dealing with idiosyncratic behavior of this particular router. That is what zapped me. Now I have to work out a fix. 
> 
> Tnx. Happy Holidays.
> 
> 73,
> 
> Brian
> 
> -- 
> 70 is the new 40.
> 
> Brian F. Wruble, C.F.A.
> 1107 Key Plaza, PMB 447 Key West, FL 33040 
> Summers: P.O.Box 57, 7400 Augustine Herman Highway, Georgetown, MD 21930    
> eFax  305.768.0278   Skype   bwruble   
> 
> 
> Begin forwarded message:
> 
>> From: "Brian F. Wruble" <bwruble at gmail.com>
>> Date: December 18, 2013 at 6:13:28 PM EST
>> To: Elecraft Reflector <elecraft at mailman.qth.net>
>> Subject: K3/0 to K3 RemoteRig issue
>> Reply-To: bwruble at gmail.com
>> 
>> Hi all:
>> 
>> I have had my remote operation working beautifully, with just problems figuring out CW and Digital, but slowly getting there.  Sideband has been fine, and I am enjoying ham radio in Key West while operating through my station on Maryland's Eastern Shore.
>> 
>> Then... I turned on the K3/0 a couple hours ago.  I heard the sounds of 40M SSB, where I had my most recent QSO.  But the dial shows 21.000.00 and  mode shown is CW.  I can tune, and obviously the distant K3 is tuning, as I can hear the signals change.  I can change bands, change modes, go in and out of XMIT.  The front panel of the K3/0 never shows a change, just sits there.
>> 
>> One possible clue:  I had an AT&T internet tech in today to give me a static ip (external ip) to support my surveillance system.  That has not affected any internet functions --- I have email, browser, and comms with the K3.  I just don't have feedback from the K3.  It seems to me that if I have good internet, then the K3/0 and RemoteRig shouldn't care about the changes, but it is suspiciously coincidental.  ........
> 
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html