[Elecraft] Vedr: K3 and MicroHam USB 3 issue

[Keith Heimbold]

Martin-

I decided to swap out the Microham usb 3 to use my other not so loaded K3 serial 1526 and in a matter of minutes with similar K3 and Microham settings everything is working perfectly well.  

The decode is also much better with both dm780 and fldigi and the Quadra is working with the Y connector with 1526.

I am not sure what is going on but three weeks ago I did do a full reset on my serial 1391 and reconfigured everything as per the manual.  

I know this sounds drastic but I am considering stripping down the fully loaded K3 and install all the goodness into 1526 and purchase the 1.8 kHz filter I have been eyeballing for awhile.

Maybe I am missing a setting or something in the slightly older K3. Need to go through the set up again most likely.

Keith
AG6AZ

Sent from my iPhone please excuse typos

On Sep 22, 2012, at 1:07 PM, "Martin Storli - LA8OKA" <arcticpeak at yahoo.no> wrote:

> Hi Keith.
>  
> Have you tried without the Y-cable?
> Have you tried with lower output?
> I think that either the Y-cable is messig up things, or that you have an RFI problem.
>  
> There are no definitive answer of what the positions on the volum knobs on the front shall be as they have to be adjusted depending on the software used, the soundcard settings and the transceiver used.
>  
> Martin Storli
> LA8OKA
> Oslo, Norway
>  
> ARCTICPEAK's Radio pages!
> http://www.arcticpeak.com/radio.htm
> 
> Fra: Keith Heimbold <ag6az at hotmail.com>
> Til: Elecraft Group <elecraft at mailman.qth.net> 
> Sendt: Lørdag, 22. september 2012 14.27
> Emne: [Elecraft] K3 and MicroHam USB 3 issue
> 
> I am going to send this out to both reflectors, Elecraft and MicroHam because I am not sure where I have set up the system incorrectly. The system does work intermittently and I have had successful QSOs with it on both CW and digital modes.
> 
> Setup;  K3, MicroHam USB 3, Y cable to ACC to USB 3 and Yaesu Quadra amp, new Asus PC running 64 bit win 7 O/S with 12 gigs of RAM.
> 
> Issue: I have intermittent performance with the USB 3 and my k3. At times when using the device with FLDigi software the transceiver ends up locking up on transmit and I usually have to exit out of FLDigi to stop the transmit cycle as none of the buttons will work. This has happened in all fldigi digital modes but is most prevalent during CW.
> 
> I am also very uncertain about the knob position on the front of the USB 3. Sorry but I can't find where the position should be in the manual. Plus I cannot seem to get five bars on the ALC meter of my K3 no matter what I try.
> 
> I am not sure if this is a K3 or USB 3 setup issue. I need a little help. It does work about 50% of the time.
> 
> Thanks,
> 
> Keith
> AG6AZ
> 
> Sent from my iPhone please excuse typos
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net/
> Please help support this email list: http://www.qsl.net/donate.html
> 
>