[Elecraft] FW: K3 no power out on DATA

Wed Sep 5 00:01:53 EDT 2012

I'll look into that...

Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ

Owner - Operator
Big Signal Ranch
Staunton, Illinois

email:  bill at wjschmidt.com

-----Original Message-----
From: elecraft-bounces at mailman.qth.net
[mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Joe Subich, W4TV
Sent: Tuesday, September 04, 2012 10:03 PM
To: elecraft at mailman.qth.net
Subject: Re: [Elecraft] FW: K3 no power out on DATA

> BTW the same cable plugged into the mic jack (on the Heil adapter) 
> doesn't work on the rear panel. Nor does anything else I plug into the 
> "line-in".

It's a long shot but make sure that L4 and L5 on the KIO3 Audio IO board are
not open.  I've had L5 (in the ground leg of the Line In
jack) fail twice.

73,

    ... Joe, W4TV

On 9/4/2012 10:38 PM, Dr. William J. Schmidt, II wrote:
> Ya know, I've got the same problem... but I've tried everything (all 
> combinations of Mic and Line-in switch and cable routings).  When I 
> was on
> J6 a few weeks ago, I got RTTY going by running the audio right into 
> the Mic jack on the front panel and turning the gain way down.  It 
> worked but I sure would like to get the "line-in" working.  Any 
> suggestions.  BTW the same cable plugged into the mic jack (on the 
> Heil adapter) doesn't work on the rear panel.  Nor does anything else 
> I plug into the "line-in".  I have not fussed with it because I had a
work-around.
>
>
> Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ
>
> Owner - Operator
> Big Signal Ranch
> Staunton, Illinois
>
> email:  bill at wjschmidt.com
>
>
> -----Original Message-----
> From: elecraft-bounces at mailman.qth.net 
> [mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Don Wilhelm
> Sent: Tuesday, September 04, 2012 4:54 PM
> To: Mike Sanders
> Cc: Elecraft Reflector
> Subject: Re: [Elecraft] K3 no power out on DATA
>
> Mike,
>
> That sounds to me as though you have the input set for MIC rather than 
> line in, or something similar.
>
> First I would suggest using Line In and use DATA mode (AFSK A 
> submode), select Line In in the MIC SEL menu.
> Set the K3 into TX TEST (or set the power down and operate into a 
> dummy
> load) - set MMTTY into transmit, then -- Adjust the line out and Wave 
> sliders on your soundcard to about 2/3 of full scale.
> Then adjust the MIC Gain (now actually Line In) to illuminate 4 bars 
> on the ALC meter with the 5th bar flashing - ignore the conventional 
> "wisdom" given for data mode setup (no alc indication) - the K3 is 
> different, the - the 1st
> 4 bars of the ALC meter do not indicate ALC at all, they are there to 
> help you adjust the audio level.  The 5th bar indicates the onset of 
> ALC
>
> 73,
> Don W3FPR
>
> On 9/4/2012 4:31 PM, Mike Sanders wrote:
>> Well, Only days old here the new K3 is still challenging me. Lots of 
>> fun without doubt. Anyway I am running MMTTY and using AFSK in the 
>> data mode. Everything looks good but no output. I tried shifting to 
>> USB/LSB and output is as set on power control. Tones on monitor and 
>> another RX sound good as well. But again when in data mode I get 
>> no/very low output. Power is set at about 50W and I get that in USB.
>> Any thoughts on what I am missing here?
>> Thanks es 73, Mike
>>
>>
>>                       Mike Sanders
>>                           KØAZ
>>
>>
>>
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net Please help support this 
>> email
>> list: http://www.qsl.net/donate.html
>>
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net Please help support this email 
> list: http://www.qsl.net/donate.html
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1424 / Virus Database: 2437/5248 - Release Date: 
> 09/04/12
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net Please help support this email 
> list: http://www.qsl.net/donate.html
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1424 / Virus Database: 2437/5249 - Release Date: 09/04/12