[Elecraft] KX3 Question

[John Strandberg]

The information on calibration of filter is in the owner's manual. The
version I have, it is on page 32 under the heading "CALIBRATION".  It
clearly states that if the filter and KX3 were ordered and shipped at the
same time, the filter calibration is not needed.

Elecraft retains configuration files for each KX3 it ships which includes
calibration data for the filter.  I know this because I made a very dumb
error in building my kit and Elecraft support worked me through the
troubleshooting process and the last try before sending back fixed it.  One
of the troubleshooting steps was to do a REINIT which sets all
configuration and calibration data back to factory default.  Once I
notified Vic in support that my problem was solved and I was going to do
the filter calibration, he came back immediately and said "Stop Don't!" and
my S/N configuration file was attached to the email.  He told me just to
upload the config file.  I uploaded it and my KX3 absolutely lit up.  It
was an amazing moment and this radio has been amazing ever since.

If you can't find the statement on no need to do filter calibration in the
manual, just repost and I'll find it in the current version manual.

73 John W4DX
On Sat, Oct 13, 2012 at 8:50 PM, Phil Hystad <phystad at mac.com> wrote:

> OK but I just looked in the assembly manual and the user guide and I did
> not see anything about NOT doing the configuration/calibration of the
> filter.  Where is this located?  I mean, the instruction saying that
> configuration/calibration of the filter is not required if shipped with the
> KX3.  By the way, even though it was shipped, I did install it and the
> configuration instructions say that the procedure must be performed
> whenever the filter is removed or replaced.
>
> What is this configuration file you mention that is associated with my
> serial number.  Is this something I need to request?
>
> Also, if this too is documented somewhere I must have missed that.  I do
> admit to not reading the user guide cover to cover yet.
>
> phil
>
>
> On Oct 13, 2012, at 5:31 PM, John Strandberg <w4dx at arrl.net> wrote:
>
> Yes. This is correct and Elecraft has a configuration file for your KX3 by
> your serial number including configuration/calibration data for any options
> such as the filter.
>
> On Sat, Oct 13, 2012 at 8:24 PM, hawley, charles j jr <
> c-hawley at illinois.edu> wrote:
>
>> Didn't the assembly manual say the if the filter is shipped with the KX3,
>> the filter doesn't need to be calibrated?
>>
>> Sent from my iPad
>>
>> On Oct 13, 2012, at 6:57 PM, "Phil Hystad" <phystad at mac.com> wrote:
>>
>> > Gang, I just finished putting together my KX3 with the filter option,
>> ATU, and battery charger.  I am just about to do the calibration for the
>> filter but I noticed that there is an LED or something that flashes, maybe
>> once per 2 seconds?, inside the KX3.  I can see it through the key/paddle
>> plug opening.
>> >
>> > Does anyone know what this is?  Is there meaning to the flash?  Is it
>> important?
>> >
>> > Thanks,
>> >
>> > 73, phil, K7PEH
>> >
>> > ______________________________________________________________
>> > Elecraft mailing list
>> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> > Help: http://mailman.qth.net/mmfaq.htm
>> > Post: mailto:Elecraft at mailman.qth.net
>> >
>> > This list hosted by: http://www.qsl.net
>> > Please help support this email list: http://www.qsl.net/donate.html
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>>
>
>
>