[Elecraft] K2 Alignment and Test, Part II - No signal on TP3

[Don Wilhelm]

Cameron,

The first thing is to determine whether you have a problem with the 
counter probe or with the PLL reference oscillator.  Plug the probe into 
TP2 and expect a reading close to 4913 to 4916 kHz.  If that is true, 
the the probe is OK.

If the probe is good, then check the PLL crystal.  It should be a 12,096 
mHz crystal.
I do not know why it would oscillate at 1817 kHz, that has no 
relationship to the proper frequency.

73,
Don W3FPR

On 7/5/2012 12:47 PM, Cameron Haines wrote:
> Good morning,
>
> I finally have my probe setup. Here is my readings which seem way off.
>
> 4 Mhz Oscillator Calibration = 1817.00 which should be reading 12090 +/- 30 kHz per manual
>
> PLL Reference Range Test
>
> Seems correct range but frequency is wrong as with Osc calibration.
>
> VCO Test
>   
> 3 - 4 kHz as opposed to 8 - 10 Mhz.
>
> Any thoughts were I have gone wrong?
>
> Thanks,
> Cameron
> AE5UZ
>
>
> ________________________________
>   From: Cameron Haines <camhaines at yahoo.com>
> To: David Moorman <dmoorman4 at comcast.net>
> Cc: "elecraft at mailman.qth.net" <elecraft at mailman.qth.net>
> Sent: Tuesday, July 3, 2012 7:40 PM
> Subject: Re: [Elecraft] K2  Alignment and Test, Part II - No signal on TP3
>   
>
> Great suggestion. I can hear it a 4Mhz now.. from my Softrock SDR. Wonder why the Freq counters couldn't pick it up however. hmm.
>
> Thanks David!
>
>
> ________________________________
>   From: David Moorman <dmoorman4 at comcast.net>
> To: Cameron Haines <camhaines at yahoo.com>
> Cc: "elecraft at mailman.qth.net" <elecraft at mailman.qth.net>
> Sent: Tuesday, July 3, 2012 7:03 PM
> Subject: Re: [Elecraft] K2  Alignment and Test, Part II - No signal on TP3
>   
> Do you have a receiver you can listen on to see if the oscillator is actually oscillating?
>
> Dave K9SW
>
>
>
> On Jul 3, 2012, at 6:41 PM, Cameron Haines <camhaines at yahoo.com> wrote:
>
>> Correction.
>>
>>
>> Hey Guys,
>>
>> Well, I am at the part where I need to test the 4 MHz oscillator calibration and ran into a snag. I am not getting anything on two different frequency counters when connected to TP3. Test up to this point have been good. Checked all the components around X1 and all look correct. No error message on startup.
>>
>> Any ideas where to go from here?
>>
>> Thanks,
>> Cameron
>> AE5UZ
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help:
>   http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>