[Elecraft] Help Please KIO2 L4 Burnt Out

[Guy Olinger K2AV]

Yikes...   That certainly would do it.  Also if memory serves me right, 260
ma is a typical K2 standing current in RX mode, almost as if the negative
power supply path to/in the K2 is just plain open somewhere.  You will have
to determine all the possible ground paths.   Let all us curious folks know
what you actually find.

Then you will need to rearrange your station wiring so that simply is not
possible.  K2 should have its own dedicated power supply with NOTHING else
on it, the same as you hear preached around here for the K3.

Good luck & 73,  Guy

On Thu, Apr 26, 2012 at 2:45 AM, VK1OO <mike.walkington at gmail.com> wrote:

>  Hi Guy,
>
> Thanks
>
> 260mA!   Guess that would do it.
> Exploring the power supply  etc now.
>
> Mike
>
>
> On 26-Apr-12 4:41 PM, Guy Olinger K2AV wrote:
>
> Do you have the DB9 plug that connects to the back of the KIO2 restricted
> to pins 2,3, 5 ONLY?  See page 21 in the KIO2 manual. If you have hooked up
> a full RS232 to the KIO2 DB9 there is no telling what has gone wrong, you
> can cause all kinds of problems.
>
>    http://www.elecraft.com/manual/KIO2_man_rev_B.pdf
>
>  Also L4 connects pin 5 of the common signal ground to the ground bus in
> the KIO2.  If that goes through to a computer where a ground (black 12V
> lead) has connected and your power supply to the K2 has a problem in the
> ground (black) 12V supply wire to the K2 somewhere, and you have other
> devices attached to the same power supply via common grounding, including
> what is connected to the computer side of the USB cable, the ground current
> attempting to flow via poor ground wire connection will attempt to find any
> alternate route to the K2 any way it can.  That ground fault will blow L4
> in the KIO2 board.
>
>  Take a DVM and see if you can draw current between pin 5 on the cable
> and the ground of the K2.  If you can, you need to solve your power supply
> problem.
>
>  73, Guy.
>
> On Thu, Apr 26, 2012 at 1:47 AM, VK1OO <mike.walkington at gmail.com> wrote:
>
>> Hi,
>>
>> My K2 rig control via a KIO2 stopped.  I discovered that RF sub
>> miniature choke L4, 100 micro Henry,  on the main KIO2 board was open
>> circuit - no evidence of excessive heat etc.  L4 is in the RS232 ground
>> path.  Shorting out L4 restored rig control.  I replaced L4 with a
>> larger version (all that I could find locally) but rig control didn't
>> work.  I tested the new L4 and it was open circuit, again no evidence of
>> excessive heat.  So the question is, what would cause excessive current
>> through L4?
>>
>> I feed the KIO2 via a USB to RS232 converter which plugs into a four
>> port USB hub which plugs into a lap top.  This combination has worked OK
>> for several years.
>>
>> Mike VK1OO
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>>
>
>