[Elecraft] SEC 1235M operating in 230 VAC

Fri Sep 9 10:15:54 EDT 2011

thanks David and Ken,

I am reading the manual, just that is difficult for me to find this jumper.
I asked Samlex for a diagram or photo to show where it´s located.

If you do that, maybe you know where is it.

73,
Jorge
CX6VM

-----Mensaje original-----
De: David Ferrington, M0XDF [mailto:M0XDF at Alphadene.co.uk] 
Enviado el: Viernes, 09 de Septiembre de 2011 10:59 a.m.
Para: Jorge Diez - CX6VM
CC: elecraft at mailman.qth.net
Asunto: Re: [Elecraft] SEC 1235M operating in 230 VAC

This site :
http://www.radiodan.com/pdf/SEC1235M_Review.pdf

say's 'internal strap change', that suggests a wire to re-solder.

This is their site:
http://www.samlexamerica.com/products/productdescription.asp?ProductsID=3602
5

there is a product manual
(http://www.samlexamerica.com/customer_support/pdf/Manuals/SEC-1235_SEC-1235
M_Manual_Sep2007.pdf) and it says:

These units have been preset to operate from an input voltage of 120 VAC, 60
Hz. The units can be set to operate from an input voltage of 230 VAC, 60 Hz.
by changing the position of an internal jumper. The procedure for conversion
to input voltage of 230 VAC, 50 Hz. is as follows:
• Switch off the unit and unplug the power cord from the AC outlet • Remove
the top cover • For 120 VAC operation (pre-set condition), points "D" and
"E" on the
printed circuit board (PCB) have been connected (shorted) with a flexible
wire jumper. To convert to 230 VAC input, disconnect the quick disconnect
connector at point "D" by pulling it upwards. Tape this end with an
insulation tape and use a cable tie to tie it securely to the wire harness
running above
• The fuse on the AC side for the preset input voltage of 120 VAC is rated
at	250 V, 8 A. For 230 VAC operation, the fuse has to be rated at 250
V, 4A. Replace the existing 8 A fuse with a 4 A fuse. See under
“SPECIFICATIONS” on page 11 for details on the 4 A fuse.
•The detachable power cord that is provided has an “IEC 320-13” female
connector on one end that will mate with the “IEC 320-C14” male AC inlet
connector on the power supply. The other end of this power cord has a 120
VAC NEMA5-15P plug meant for connection to the 120 VAC, NEMA5-15R outlet.
For operation on 230 VAC, 50 Hz, a different detachable power cord will have
to be used. Use an appropriate power cord that has an “IEC 320-13” female
connector on one end (for connection to the “IEC 320-C14” AC inlet connector
on the power supply) and a 230 VAC plug on the other end corresponding to
the 230 VAC outlet. Please ensure that the new 230 VAC power cord uses two
pole, 3 wire grounding configuration (this will ensure proper earth
grounding).
3.
FEATURES
OPERATION FROM AC INPUT VOLTAGE OF 230 VAC
CONNECTION AND OPERATION
WARNING ! The unit has been pre-set to operate from an input voltage of 120
VAC. Hence, before plugging the unit to the AC outlet, please ensure that
the local AC power supply voltage is 120 VAC. Operation from 230 VAC is
possible by changing internal settings. Please see details on page 3 under
“OPERATION FROM AC INPUT VOLTAGE OF
230 VAC”

-- 
The rung of a ladder was never meant to rest upon, but only to hold a man's
foot long enough to enable him to put the other somewhat higher.
-Thomas Henry Huxley, biologist and writer (1825-1995)

On 9 Sep 2011, at 14:42, Jorge Diez - CX6VM wrote:

> Hello,
> 
> 
> 
> while waiting for Samlex answer, maybe someone using a Samlex SEC 1235M
can
> help me to find the jumper to switch from 120 to 230 VAC?
> 
> 
> 
> I bought this PS that was recommended in this list, but really I couldn’t
> find this jumper to start using it at 230 VAC
> 
> 
> 
> thanks,
> 
> Jorge
> 
> CX6VM
> 
> k3 #4077
> 
> 
> 
> De: Jorge Diez - CX6VM [mailto:cx6vm.jorge at gmail.com] 
> Enviado el: Jueves, 08 de Septiembre de 2011 08:33 p.m.
> Para: 'tech at samlexamerica.com'
> Asunto: SEC 1235M operating in 230 VAC
> 
> 
> 
> Hello,
> 
> 
> 
> some months ago I bought in USA a SEC 1235M,  S/N 03435-1032-00003
> 
> 
> 
> I am going to use it now with 230 VAC, but I couldn´t find the jumper to
> change from 120 VAC to 230 VAC.
> 
> 
> 
> Do you have a photo to show me where is it?
> 
> 
> 
> thanks,
> 
> Jorge
> 
> CX6VM
> 
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html