[Elecraft] Fwd: [FlexEdge] Field Day, Focus and Contest Skins?

[W6NEK]

Hi Brett,
If you must run with AVG ON then a good compromise is to set the "AVG" 
Averaging Time from 350 milliseconds (default) down to 50 milliseconds.  The 
adjustment is located under the PowerSDR Setup Menu in the Display Tab.  The 
control is titled Averaging - Time(ms).  Or you can set it to any value from 
1 to 350ms to your liking.

Best 73,
Frank - W6NEK

----- Original Message ----- 
From: "Brett Howard" <brett at livecomputers.com>
To: "W6NEK" <w6nek at socal.rr.com>
Cc: "Elecraft Group" <elecraft at mailman.qth.net>
Sent: Monday, June 28, 2010 3:03 PM
Subject: Re: [Elecraft] Fwd: [FlexEdge] Field Day, Focus and Contest Skins?


> Yea I kinda noticed that... But I felt like I was about to enter into a
> seizure when its real time...
>
> I'm not sure what would work better but two interesting things to see
> would be either have the display go into real time mode during a QSY or
> have the display freeze the averaged data during QSY.  I'm not as
> certain about that second idea but there are maybe some slight
> modifications of that that could be interesting...
>
> ~Brett (N7MG)
>
> On Mon, 2010-06-28 at 14:59 -0700, W6NEK wrote:
>> Hi Brett,
>> What you describe is commensurate with the PowerSDR Display "AVG" Mode 
>> being
>> enabled.  If "AVG" Mode is off, the displayed panadapter signal amplitude
>> will not decrease as you tune the band.  The displayed signals are 
>> real-time
>> with a display frame rate adjustable to 50 frames per second.  Just click
>> the AVG Button off.
>>
>> 73,
>> Frank - W6NEK
>>
>> ----- Original Message ----- 
>> From: "Brett Howard" <brett at livecomputers.com>
>> To: "Lyle Johnson" <kk7p at wavecable.com>
>> Cc: "Elecraft Group" <elecraft at mailman.qth.net>
>> Sent: Monday, June 28, 2010 12:57 PM
>> Subject: Re: [Elecraft] Fwd: [FlexEdge] Field Day, Focus and Contest 
>> Skins?
>>
>>
>> <SNIP>
>> Many also didn't like the slight lag in turning the knob and seeing
>> the signals.  As you tune the knob on the K3 the signals kinda drop
>> out and you have to stop your QSY then let the signals come up out of
>> the noise again and then dial into it...  I hope that the P3 is a lot
>> faster and the signals stay visible while fast QSYing.  I don't
>> remember being able to do a whole lot of that when I saw it in Seaside
>> but there weren't a lot of signals all over just the 4 that were in
>> the recorder...
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>
>


--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 9.0.830 / Virus Database: 271.1.1/2968 - Release Date: 06/27/10 
23:37:00