[Elecraft] K3 ESSB macro

[Mike]

I don't think you can. Doing it manually on the radio is a toggle, it 
switches state AFAICS. The macro is just emulating that.

Mike NF4L

Barry N1EU wrote:
> Yes, but you can't embed a conditional statement in a macro so being
> able to read the current ESSB state doesn't help.   So under the
> constraints of macro coding, how to turn ESSB on/off independent of
> current state of ESSB?
>
> Tnx/73,
> Barry N1EU
>
> On Mon, Jan 18, 2010 at 12:15 AM, Greg <ab7r at cablespeed.com> wrote:
>   
>> Ooops....no bug.  Radio was in CW mode.  Duh!
>>
>> The first line show ESSB off, second line shows ESSB on.
>>
>> IC\x80\xA8\x94\x90\x80;
>>
>> IC\x80\xA8\x94\xB0\x80;
>>
>> So the status of Byte D tells you the status of ESSB.
>>
>> 73
>> Greg
>>
>>
>>
>> On 1/17/2010 4:05 PM, Greg wrote:
>>
>> When looking at this Barry I thought maybe you could read the status of the
>> "+" icon on the LCD.  That is supposed to be on if ESSB is on.  I think a
>> bug got into the FW where the icon is no longer showing when in ESSB.
>>
>> This is from the current Programmer's manual...
>>
>> IC * (Misc. Icons and Status; GET only)
>> RSP format: ICabcde; where abcde are ASCII characters (Byte in Table 4
>> below) used as collections flags (Bit
>> in table). Each flag represents the status of an LCD icon and/or specific
>> transceiver function.
>> Some functions whose status is indicated by IC command flags can be
>> controlled using emulation commands. For
>> example, the K3 can be put into TX TEST by sending SWH18. The condition can
>> be verified at any time using the
>> IC command (byte a, bit 5). Another example: ESSB (extended SSB) can be
>> turned on/off using an MN (menu)
>> command, followed by SWT11, simulating a tap of 1 on the keypad. Again, IC
>> can be used to verify the present
>> state (byte d, bit 5).
>>
>>
>> 73
>> Greg
>> AB7R
>>
>>
>>
>>
>>
>> On 1/17/2010 12:35 PM, Barry N1EU wrote:
>>
>> Can someone please confirm:  it is possible to toggle the TX ESSB on/off
>> value via macro (mn096;swt11;mn255;) but it is impossible to set it to a
>> known value of "on" or "off" ?
>>
>> Thanks/73,
>> Barry N1EU
>>
>>
>> No virus found in this incoming message.
>> Checked by AVG - www.avg.com
>> Version: 8.5.432 / Virus Database: 270.14.147/2628 - Release Date: 01/17/10
>> 07:35:00
>>
>>
>>
>> No virus found in this incoming message.
>> Checked by AVG - www.avg.com
>> Version: 8.5.432 / Virus Database: 270.14.147/2628 - Release Date: 01/17/10
>> 07:35:00
>>
>>
>>     
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html