[Elecraft] K3 Firmware 2.58

[Bill Johnson]

Wayne, Joe and Julian,

Thank you!  I will change to the 0051.  If I want lower will send 0050.  One
watt increments work for me.  I usually use 2 watts or 75, very little in
between.  I will use my K2 for variations in between if I so choose.  


73,

Bill
K9YEQ
K2 #35; KX1 #35; K3 #1744; mini mods


-----Original Message-----
From: elecraft-bounces at mailman.qth.net
[mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Joe Subich, W4TV
Sent: Friday, October 31, 2008 6:53 PM
To: 'Julian, G4ILO'; elecraft at mailman.qth.net
Subject: RE: [Elecraft] K3 Firmware 2.58


Julian, 

Assuming you are using the K22; extended mode, use 
PC0051; to set 5 Watts (5 Watts, high range).  The 
PC0500; sets to 5.0 Watts in the low range (turns 
off the PA).  

The only downside to using the PC0051; syntax is that 
you can't set the power to other than integral values 
of power (2.0, 3.0, 4.0, etc. Watts).  

73, 

   ... Joe, W4TV 
   



> -----Original Message-----
> From: elecraft-bounces at mailman.qth.net 
> [mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Julian, G4ILO
> Sent: Friday, October 31, 2008 5:44 PM
> To: elecraft at mailman.qth.net
> Subject: RE: [Elecraft] K3 Firmware 2.58
> 
> 
> 
> 
> 
> Bill Johnson-9 wrote:
> > 
> > Julian,
> > 
> > Here's what's in the command:  PC0500;PC;DS;
> > 
> > I tried it again and I get the same thing.  The power cannot be 
> > adjusted with the front panel dial past 12 watts.
> > 
> > 
> > Bill
> > 
> You are right. Perhaps someone can advise how to reduce power 
> to below 12W by software command without disabling the 
> ability to increase it above that level again using the front 
> panel control.
> 
> -----
> Julian, G4ILO. K2 #392  K3 #222.
> http://www.g4ilo.com/ G4ILO's Shack   
> http://www.ham-directory.com/ Ham
> Directory    http://www.g4ilo.com/kcomm.html KComm for 
> Elecraft K2 and K3 
> -- 
> View this message in context: 
> http://n2.nabble.com/K3-Firmware-2.58-tp1437773p1438626.html
> Sent from the Elecraft mailing list archive at Nabble.com.
> 
> _______________________________________________
> Elecraft mailing list
> Post to: Elecraft at mailman.qth.net
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft    
> 
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com

_______________________________________________
Elecraft mailing list
Post to: Elecraft at mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft    

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com