[Elecraft] Band decoder and Tx Inhibit

[Greg - AB7R]

 Only issue is that the Mic and Headphone jacks on the back 
>are pretty frail and don't make very positive contact sometimes.

Andy,  Are you using 1/8-in plugs or 3.5mm?

-------------------------
73,
Greg - AB7R
Whidbey Island WA
NA-065
K3#0009

On Tue Jan 29 15:07 , "Andrew Faber"  sent:

>Chris,
> Good luck with it.  I have the TT Decoder powered by an independent 12 volt 
>source.  It has internal pull-up resistors, so there appears to be no 
>connection needed other than the ones I mentioned.  It took me a bunch of 
>trial and error time to figure this out.  Let us know how it works.
>  I emailed N3RD a while ago to let them know.  Dave said he had a K3 on 
>order, and that they did intend to offer K3 cables.  I made up a "generic" 
>cable from my TT DX Doubler to the K3, and that seems to work well also. 
>It's nice to use inputs all on the back of the K3, so there are no cables to 
>the front panel.  Only issue is that the Mic and Headphone jacks on the back 
>are pretty frail and don't make very positive contact sometimes.
>  73, andy, ae6y
>----- Original Message ----- 
>From: "G3SJJ" g3sjj at btinternet.com>
>Cc: "Elecraft" elecraft at mailman.qth.net>
>Sent: Tuesday, January 29, 2008 3:01 PM
>Subject: Re: [Elecraft] Band decoder and Tx Inhibit
>
>
>> Oh thanks for that Andy. I'll get it wired up in the morning with 
>> confidence then! I know that Dave N3RD (of Top Ten) and Sig N3RS are 
>> eagerly awaiting their K3s and will also be interested.
>>
>> 73 Chris G3SJJ
>>
>>
>>
>> Andrew Faber wrote:
>>> Chris,
>>>  I have my K3 hooked up to a Top Ten Yaesu decoder, and it seems to work 
>>> fine.  You need to connect 5 wires: the four BCD outputs and ground. 
>>> Once I figured out the pin numbering it was straightforward  (Pins on the 
>>> ACC jack are numbered 1-5, 6-10, 11-15 from right to left and top to 
>>> bottom, looking at the radio from the back).
>>>  73, andy, ae6y
>>> ----- Original Message ----- From: "G3SJJ" g3sjj at btinternet.com>
>>> To: "Elecraft" elecraft at mailman.qth.net>
>>> Sent: Tuesday, January 29, 2008 11:46 AM
>>> Subject: [Elecraft] Band decoder and Tx Inhibit
>>>
>>>
>>>> I wondered if any has connected up a TT Band Decoder to the ACC socket 
>>>> yet. I am just about to make up a suitable cable. Also theer was some 
>>>> discussion somewhile back about TX Inhibit for connecting to amps. 
>>>> Anyone done this. I see it needs an external +5v source.
>>>>
>>>> On my FT1kMP use the band data out socket f for my TT Decoder and pick 
>>>> up +12v from there, also amp relay switching. Would have been nice on 
>>>> the K3!
>>>>
>>>> Chris G3SJJ
>>>> _______________________________________________
>>>> Elecraft mailing list
>>>> Post to: Elecraft at mailman.qth.net
>>>> You must be a subscriber to post to the list.
>>>> Subscriber Info (Addr. Change, sub, unsub etc.):
>>>> http://mailman.qth.net/mailman/listinfo/elecraft
>>>> Help: http://mailman.qth.net/subscribers.htm
>>>> Elecraft web page: http://www.elecraft.com
>>>>
>>>
>>>
>>>
>> _______________________________________________
>> Elecraft mailing list
>> Post to: Elecraft at mailman.qth.net
>> You must be a subscriber to post to the list.
>> Subscriber Info (Addr. Change, sub, unsub etc.):
>> http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/subscribers.htm
>> Elecraft web page: http://www.elecraft.com
>> 
>
>
>_______________________________________________
>Elecraft mailing list
>Post to: Elecraft at mailman.qth.net
>You must be a subscriber to post to the list.
>Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft    
>
>Help: http://mailman.qth.net/subscribers.htm
>Elecraft web page: http://www.elecraft.com