[Elecraft] [Fwd: [Fwd: K3 #0215.....HELP!]]
Greg
ab7r at cablespeed.com
Sun Jan 20 14:39:35 EST 2008
If you are using the USB interface, please see the notes on the Elecraft
Software page about updating your drivers for the interface, then update the
K3 again.
Tnx.
73
Greg
AB7R
-----Original Message-----
From: elecraft-bounces at mailman.qth.net
[mailto:elecraft-bounces at mailman.qth.net]On Behalf Of Thomas Norff
Sent: Sunday, January 20, 2008 6:11 AM
To: 'Mike'
Cc: Elecraft at mailman.qth.net
Subject: RE: [Elecraft] [Fwd: [Fwd: K3 #0215.....HELP!]]
Hi Mike,
there seems to be no DSP Software ?
D1 should show 1.48
Try to load the DSP Software again.
Thomas, DM7TN
K3/100 #78
-----Original Message-----
From: elecraft-bounces at mailman.qth.net
[mailto:elecraft-bounces at mailman.qth.net] On Behalf Of Mike
Sent: Sunday, January 20, 2008 8:15 AM
To: Elecraft at mailman.qth.net
Subject: [Elecraft] [Fwd: [Fwd: K3 #0215.....HELP!]]
Hi Everyone - I just sent the following to Support, but, as its weekend,
guess will be a while before I can expect a reply!
Meantime, does anyone on the list have any (helpful) suggestions please?
Its only the DSP that didn't update, the MCU went from 1.48 to 1.58, no
problem!
As I'm on dialup (& Digest) any direct replies welcome.
73, Mike, zl1mh.
Further to the info. below....
Rig worked fine until the download.
There is nil audio output from the rig on either SP or PH.
uC updated ok from 1.47 to 1.58 on the same download.
Menu FW REVS shows the following....uC 01.58
d1 00.00
d2 00.00
FL 00.00
dr 00.00
If I go into SQ Menu, only -- shows on the (A) display. There is no
available SQ adjustment.
HTH!
Mike, zl1mh.
Greetings folks!
#0215 was up & working fine (No PA installed as yet).
This morning I went to do a firmware download/update from your website.
All goes well on the connection/download etc., I then get the following
message(s) when I try to instal the new f/w to my K3.
DSP1 f/w file TBOOT7.HEX verified
DSP1 f/w file HDSP01.48.HEX verified
DSP1 f/w file DTBL0004.HEX verified
Sending f/w file TBOOT7.HEX to DSP1
Erasing DSP1 program & table memory
Sending f/w file HDSP01.48.HEX to DSP1
Sending f/w file DTBL0004.HEX to DSP1
waiting for MCU reset to complete
verifying DSP1 program load
Loaded DSP1 f/w version 01.48 Radio responded with version 00.00
On the K3 Display, I get E 000202
Err dse
If I sweitch the K3 OFF & ON again, I get the same message on the Display.
I am using the USB/Ser adaptor from Elecraft, & have the latest Driver from
Prodogy.
All appeared fine until this Download!
HELP!! (And TIA!!).
73.....Mike, zl1mh.
_______________________________________________
Elecraft mailing list
Post to: Elecraft at mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: Elecraft at mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
More information about the Elecraft
mailing list