[Elecraft] Spam bounce?

[Mike W]

AFIK, and certainly in UK, the Wanadoo ISP is far from Freemail. I'm 
on Freeserve which is the UK Name for Wanadoo and I have never 
experienced a bounce because of my ISP's policies.
I can't offer any good reasons why they are bouncing though sO I 
suppose I had better stop using bandwidth.
73 Mike G8NXD
--  


On 9 Apr 2005 at 10:09, Martin Kratoska wrote:

> It seems that the general settings of spam filtering is the culprit.
> Some ISP blocking mass freemail providers (yahoo.com, aol.com etc.).
> An email address change is the solution.
> 
> 73 Martin OK1RR
> 
> 
> F5UL napsal(a):
> > May be out of order on this reflector, but yesterday I had a mssage
> > to post concerning a big trouble with my K2 SN 4498 and the
> > following was all what I got in return...!!! So what can I do to
> > post an e-mail from Europe????????????? Thank you very much for the
> > pass band ! F5UL
> > --------------------------------------------------------------------
> > -------- --------------------------------------------------
> > 
> > Reporting-MTA: dns; wanadoo.fr
> > X-SMTP-Server-Queue-ID: 8B4D31C00152
> > X-SMTP-Server-Sender: rfc822; ars.f5ul at wanadoo.fr
> > Arrival-Date: Fri,  8 Apr 2005 22:47:17 +0200 (CEST)
> > 
> > Final-Recipient: rfc822; elecraft at mailman.qth.net
> > Action: failed
> > Status: 5.0.0
> > Diagnostic-Code: X-SMTP-Server; host
> > 
> > --------------------------------------------------------------------
> > -------- ------------------------------------------------- Hello the
> > list, Up to this morning, this K2 was a nice and good worker, with
> > during the last six month about a thousand QSO under his belt ! But
> > this morning turning it on, I just got a vigorous howl ( very low
> > freq nois !). I turn it off, and on after a few second. The Rx start
> > normaly and the noise start again after a few second. Re-turn off
> > and tunr on and no howl and Rx is working correctly! The set was in
> > CW mode so I turn down power (to abt 2/3 watts) and close the key...
> > The result is correct on 1.8, 3.5, 7.0 but nil on the rest of the
> > bands. Closing the key a little longer  on 7.0 the rig goes to
> > curent overange in abt 10/12 second and power fall down to zero. So
> > power off, open the rig, remove the bottom cover and before removing
> > the heat sink just check the resistance of driver and PAOn Q6
> > (driver) E to Gnd 1.3 ohm, B to Gnd 76/80 ohms, and C to Gnd > 500
> > ohms. On Pa C to Gnd > 600 ohms, B to Gnd 120/130 ohm E to Gnd 0
> > (it's normal!)They seems to be normals but any time I close the key
> > I get High Cur and power out ZERO !! I do n,ot know what to do so I
> > will wait till tomorow and hope to get some indications from the
> > list ! Thanks in advance guy, BCNU 72 Bob/F5UL
> > 
> > 
> > 
> > 
> > _______________________________________________
> > Elecraft mailing list
> > Post to: Elecraft at mailman.qth.net
> > You must be a subscriber to post to the list.
> > Subscriber Info (Addr. Change, sub, unsub etc.):
> >  http://mailman.qth.net/mailman/listinfo/elecraft    
> > 
> > Help: http://mailman.qth.net/subscribers.htm
> > Elecraft web page: http://www.elecraft.com
> > 
> 
> _______________________________________________
> Elecraft mailing list
> Post to: Elecraft at mailman.qth.net
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft    
> 
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>