FW: [Elecraft] Stuck Again -- Sorta!

Thu Dec 5 08:33:00 2002

OK, let's back up again. 

Your original post requested info on the location of RP1 on the Control
Board. Now, you are describing the Front Panel Board. 

Again, let me strongly suggest you download the manual in PDF form from the
Elecraft Website, and search that to answer these, and similar questions.

The link for the manual is:
http://www.elecraft.com/manual/K2%20man%20rev%20D%20web.pdf

If you don't have the Adobe Reader:
http://www.adobe.com/products/acrobat/readstep2.html

The RP1 on the Front Panel board is along the right side (fartherest away
from J2) along the edge.

Dan / WG4S / K2 #2456

-----Original Message-----
From: [email protected]
[mailto:[email protected]]On Behalf Of Crashin J
Sent: Wednesday, December 04, 2002 9:08 PM
To: Dan Barker; Elecraft
Subject: Re: [Elecraft] Stuck Again -- Sorta!

Ok, now I'm really confused! My Front Panel board only has 3 transistors on
it, your say it has 4??? Q1 & Q2 are below U1. Then Q3 is to the left and
below Q1 & Q2. In fact on my board Q3 is right about RP3? I'm really
confused now, where is RP1 suppose to be?

Jerry - NR5A
----- Original Message -----
From: "Dan Barker" <[email protected]>
To: "Elecraft" <[email protected]>
Sent: Wednesday, December 04, 2002 6:50 PM
Subject: FW: [Elecraft] Stuck Again -- Sorta!

> Use the PDF Version of the manual. Do a Locate (Find) on RP1. You'll see
all
> the references to RP1 in the book, including the instructions (you found
> that), the schematic (interesting, but doesn't help here) and the parts
> placement diagram (Oh yeah!). You'll see RP1 goes above the PIC chip and
> below 4 transistors (Q1-4).
>
> Dan / WG4S / K2 #2456
>
> -----Original Message-----
> From: [email protected]
> [mailto:[email protected]]On Behalf Of Crashin J
> Sent: Wednesday, December 04, 2002 8:21 PM
> To: elecraft
> Subject: [Elecraft] Stuck Again -- Sorta!
>
>
> Ok, on the Control Panel board the manual says to put in RP1 which is a
sip
> resistor. Looking at the board I can't find a RP1! I do see a RP3 which is
> right above R3 & R4. Did I somehow overlook something? Where does RP1 go?
>
> Jerry - NR5A
>
> _______________________________________________
> Elecraft mailing list: [email protected]
> You must be a list member to post to the list.
> Postings must be plain text (no HTML or attachments).
> See: http://mailman.qth.net/mailman/listinfo/elecraft
> Elecraft Web Page: http://www.elecraft.com
>
> _______________________________________________
> Elecraft mailing list: [email protected]
> You must be a list member to post to the list.
> Postings must be plain text (no HTML or attachments).
> See: http://mailman.qth.net/mailman/listinfo/elecraft
> Elecraft Web Page: http://www.elecraft.com
>

_______________________________________________
Elecraft mailing list: [email protected]
You must be a list member to post to the list. 
Postings must be plain text (no HTML or attachments). 
See: http://mailman.qth.net/mailman/listinfo/elecraft
Elecraft Web Page: http://www.elecraft.com

--- StripMime Report -- processed MIME parts ---
multipart/mixed
  text/plain (text body -- kept)
  application/ms-tnef
The reason this message is shown is because the post was in HTML
or had an attachment. Attachments are not allowed.
Please post in Plain-Text only.---