From 4z1uf at bezeqint.net Mon Jun 10 15:45:17 2019 From: 4z1uf at bezeqint.net (Ilya Zozin,4Z1UF) Date: Mon, 10 Jun 2019 22:45:17 +0300 Subject: [Dxbase] OmniRig support Message-ID: <00cb01d51fc5$082f17a0$188d46e0$@bezeqint.net> Hello all, Does DXbase2007 works with OmniRig? Thanks and 73, Ilya, 4Z1UF From post at lb3re.com Mon Jun 10 16:43:19 2019 From: post at lb3re.com (Stein-Roar Brobakken) Date: Mon, 10 Jun 2019 22:43:19 +0200 Subject: [Dxbase] OmniRig support In-Reply-To: <00cb01d51fc5$082f17a0$188d46e0$@bezeqint.net> References: <00cb01d51fc5$082f17a0$188d46e0$@bezeqint.net> Message-ID: <92BB4F0F-DD31-4FCB-8CE2-C7A078B352F0@lb3re.com> Hello I think no, because only straigth comports only! You can use serial splitter software or comport server Best Regards, Stein-Roar Brobakken post at lb3re.com LB3RE K3RAG Skype: lb3re.rag > 10. jun. 2019 kl. 21:45 skrev Ilya Zozin,4Z1UF <4z1uf at bezeqint.net>: > > Hello all, > Does DXbase2007 works with OmniRig? > > Thanks and 73, > Ilya, 4Z1UF > > ______________________________________________________________ > Dxbase mailing list > Home: http://mailman.qth.net/mailman/listinfo/dxbase > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Dxbase at mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html From lladerman at earthlink.net Mon Jun 10 18:20:46 2019 From: lladerman at earthlink.net (Lou Laderman) Date: Mon, 10 Jun 2019 17:20:46 -0500 Subject: [Dxbase] FW: Dxbase Digest, Vol 177, Issue 1 References: Message-ID: <001f01d51fda$c0553980$40ffac80$@earthlink.net> Greg, I tried emailing you directly, but the email bounced. I got my 7610 working with DXBase very easily my modifying the C-IV address in the IC-7600_DW_ok_SPLIT_ok radio.ini file to Address=0x98. Easy cut and paste. Any of the 7600 radio.ini files will work just fine if you change the C-IV address. Here's the entire set with my adder for the 7610. 73 Lou, W0FK [ICOM_IC-7610-7600_DW_ok_SPLT_ok] #IC-7610 - 7600 DUALWATCH OK and SPLIT OK by WA6AXE N5IN W0FK P_LSB=0 P_USB=1 P_CW_USB=0 P_CW_LSB=0 P_AM=2 P_FM=5 P_FM_N=0 P_DATA_LSB=0 P_DATA_USB=0 P_DATA_FM=0 P_CW=3 P_FSK=4 P_RTTY=4 P_PACKET=4 P_CWR=3 LSB=0 USB=1 AM=2 CW=3 FSK=4 RTTY=4 FM=5 CWR=3 HIGH=1 MEDIUM=2 LOW=2 Address=0x98 PACING=5 FREQDIVIN=1 FREQDIVOUT=1 USEEXTENDEDMODES=0 FREQSHIFT=0 DefaultCW=3 DefaultFSK=4 DefaultRTTY=4 DefaultFM=5 DefaultAM=2 DefaultCWR=3 SelectVFOA= hex(fe) hex(fe) hex(%ra) hex(e0) hex(07) hex(d0) hex(fd) eoc(100) SetVFOA= hex(fe) hex(fe) hex(%ra) hex(e0) hex(00) bcd(%vfoa,5) hex(fd) eoc(100) hex(fe) hex(fe) hex(%ra) hex(e0) hex(07) hex(c0) hex(fd) eoc(100) GetVFOA= hex(fe) hex(fe) hex(%ra) hex(e0) hex(03) hex(fd) rrs(16) eoc(100) PrsVFOA= hex(%dummy, 11) bcd(%vfoa,5) eoc(0) SelectVFOB= hex(fe) hex(fe) hex(%ra) hex(e0) hex(07) hex(d1) hex(fd) eoc(100) SetVFOB= hex(fe) hex(fe) hex(%ra) hex(e0) hex(00) bcd(%vfob,5) hex(fd) eoc(100) hex(fe) hex(fe) hex(%ra) hex(e0) hex(07) hex(c1) hex(fd) eoc(100) GetVFOB= hex(fe) hex(fe) hex(%ra) hex(e0) hex(03) hex(fd) rrs(16) eoc(100) PrsVFOB= hex(%dummy, 11) bcd(%vfob,5) eoc(0) SetMode= hex(fe) hex(fe) hex(%ra) hex(e0) hex(06) hex(%mode) hex(fd) eoc(100) GetMode= hex(fe) hex(fe) hex(%ra) hex(e0) hex(04) hex(fd) rrs(13) eoc(100) PrsMode= hex(%dummy, 11) hex(%mode) hex(%dummy) eoc(0) SetFilter= hex(fe) hex(fe) hex(%ra) hex(e0) hex(06) nib("%mode %filter") hex(fd) eoc(100) GetFilter= hex(fe) hex(fe) hex(%ra) hex(e0) hex(04) hex(fd) eoc(100) PrsFilter= hex(fe) hex(fe) hex(e0) hex(%dummy) hex(04) nib("%mode %filter") hex(fd) eoc(0) SetSplit= hex(fe) hex(fe) hex(%ra) hex(e0) hex(0f) hex(%split) hex(fd) eoc(100) GetSplit= hex(fe) hex(fe) hex(%ra) hex(e0) hex(0f) hex(fd) rrs(13) eoc(100) PrsSplit= hex(%dummy, 11) hex(%split) hex(%dummy) eoc(0) Message: 3 Date: Sun, 19 May 2019 20:50:35 -0400 From: < gyates at dreamscape.com> To: < dxbase at mailman.qth.net> Subject: [Dxbase] DXBase and IC7610 Message-ID: < 000001d50ea6$09d40eb0$1d7c2c10$@dreamscape.com> Content-Type: text/plain; charset="us-ascii" Is any one using DXBase with an IC7610? If so, would you share your settings? I have been trying to get DXBase to talk to 7610 without any success. Thanks, Greg, WB2BIN From k4xp.dx at k4xp.com Mon Jun 10 21:32:23 2019 From: k4xp.dx at k4xp.com (Keith Lewis) Date: Tue, 11 Jun 2019 01:32:23 +0000 Subject: [Dxbase] IC-7610 with DXbase Message-ID: <3b58b092-bc7e-5bcf-fd11-010f275a2b12@k4xp.com> Greg, WB2BIN I use DXbase with the IC-7610. Set DXbase to IC-7600 and change the IC-7610 CI-V address to 7Ah which is the same as the IC-7600. Baud rate of 9600 seems to work the best so set the IC-7610 for 9600 and DXbase for 9600. Word: 8,? Parity: None, ? Stop Bits: 1 No check mark in DTR, RTS or CTS 73,? Keith? K4XP From 4z1uf at bezeqint.net Tue Jun 11 02:23:13 2019 From: 4z1uf at bezeqint.net (Ilya Zozin, 4Z1UF) Date: Tue, 11 Jun 2019 09:23:13 +0300 Subject: [Dxbase] OmniRig support In-Reply-To: <92BB4F0F-DD31-4FCB-8CE2-C7A078B352F0@lb3re.com> References: <00cb01d51fc5$082f17a0$188d46e0$@bezeqint.net> <92BB4F0F-DD31-4FCB-8CE2-C7A078B352F0@lb3re.com> Message-ID: Thanks to all who answered. I'm using for years the LPB2 Bridge with everything I need, but when I decided to go FT8- found out that I cannot mate WSJT-X with LPB2. Will look for another solution. ?73, Ilya, 4Z1UF Sent from TypeApp ? On Jun 10, 2019, 23:43, at 23:43, Stein-Roar Brobakken wrote: >Hello > >I think no, because only straigth comports only! > >You can use serial splitter software or comport server > >Best Regards, >Stein-Roar Brobakken >post at lb3re.com >LB3RE K3RAG >Skype: lb3re.rag > >> 10. jun. 2019 kl. 21:45 skrev Ilya Zozin,4Z1UF <4z1uf at bezeqint.net>: >> >> Hello all, >> Does DXbase2007 works with OmniRig? >> >> Thanks and 73, >> Ilya, 4Z1UF >> >> ______________________________________________________________ >> Dxbase mailing list >> Home: http://mailman.qth.net/mailman/listinfo/dxbase >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Dxbase at mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html From post at lb3re.com Tue Jun 11 03:16:08 2019 From: post at lb3re.com (Stein-Roar Brobakken) Date: Tue, 11 Jun 2019 09:16:08 +0200 Subject: [Dxbase] OmniRig support In-Reply-To: References: <00cb01d51fc5$082f17a0$188d46e0$@bezeqint.net> <92BB4F0F-DD31-4FCB-8CE2-C7A078B352F0@lb3re.com> Message-ID: <977CC7AB-2D12-4643-BB71-FA6CA64BDD11@lb3re.com> I use microham mkii Then use have two comports straigth in urouter software. Best Regards, Stein-Roar Brobakken post at lb3re.com LB3RE K3RAG Skype: lb3re.rag > 11. jun. 2019 kl. 08:23 skrev Ilya Zozin, 4Z1UF <4z1uf at bezeqint.net>: > > Thanks to all who answered. > I'm using for years the LPB2 Bridge with everything I need, but when I decided to go FT8- found out that I cannot mate WSJT-X with LPB2. > Will look for another solution. > > 73, > Ilya, 4Z1UF > > Sent from TypeApp >> On Jun 10, 2019, at 23:43, Stein-Roar Brobakken wrote: >> Hello >> >> I think no, because only straigth comports only! >> >> You can use serial splitter software or comport server >> >> Best Regards, >> Stein-Roar Brobakken >> post at lb3re.com >> LB3RE K3RAG >> Skype: lb3re.rag >> >>> 10. jun. 2019 kl. 21:45 skrev Ilya Zozin,4Z1UF <4z1uf at bezeqint.net>: >>> >>> Hello all, >>> Does DXbase2007 works with OmniRig? >>> >>> Thanks and 73, >>> Ilya, 4Z1UF >>> >>> >>> Dxbase mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/dxbase >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Dxbase at mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html From n1nk at cox.net Fri Jun 14 07:08:34 2019 From: n1nk at cox.net (Jim Spears) Date: Fri, 14 Jun 2019 07:08:34 -0400 Subject: [Dxbase] missing database at startup Message-ID: <000c01d522a1$83096e10$891c4a30$@cox.net> I had a system crash and the machine on which a DXbase2007 database resided no longer exists. This situation has been cleaned up except for one system which had the prompt for database and column order at startup enabled. Now when I start DXbase on that system, an error box appears (which is OK) but when OK is clicked, DXbase exits without giving me a chance to correct the error condition. Where is this prompt stored in configuration data? It must be somewhere that I can modify. Else it appears that the only recourse is to reinstall the program. Jim/N1NK From fred at g4bwp.com Fri Jun 14 07:43:21 2019 From: fred at g4bwp.com (Fred Handscombe) Date: Fri, 14 Jun 2019 11:43:21 +0000 Subject: [Dxbase] missing database at startup In-Reply-To: <000c01d522a1$83096e10$891c4a30$@cox.net> References: <000c01d522a1$83096e10$891c4a30$@cox.net> Message-ID: Hi Jim I have that T shirt! On my PC in C:\Windows there is a file called "Dxb2007" labelled configuration settings Note NOT the same file in your DXBase2007 install directory The config file is flat text so can be edited with Notepad etc Scroll down the to section headed [DIR} Below that you can enter the path for the new location of your log book under DATAPATH, then it should find it Ok and boot Best to save DXBase config with a new name first! 73 Fred G4BWP www.g4bwp.com Hoarder of fine valved radios ------ Original Message ------ From: "Jim Spears" To: dxbase at mailman.qth.net Sent: 14/06/2019 12:08:34 Subject: [Dxbase] missing database at startup >I had a system crash and the machine on which a DXbase2007 database resided >no longer exists. This situation has been cleaned up except for one system >which had the prompt for database and column order at startup enabled. > > > >Now when I start DXbase on that system, an error box appears (which is OK) >but when OK is clicked, DXbase exits without giving me a chance to correct >the error condition. > > > >Where is this prompt stored in configuration data? It must be somewhere >that I can modify. Else it appears that the only recourse is to reinstall >the program. > > > >Jim/N1NK > >______________________________________________________________ >Dxbase mailing list >Home: http://mailman.qth.net/mailman/listinfo/dxbase >Help: http://mailman.qth.net/mmfaq.htm >Post: mailto:Dxbase at mailman.qth.net > >This list hosted by: http://www.qsl.net >Please help support this email list: http://www.qsl.net/donate.html From n4tl2 at yahoo.com Fri Jun 14 15:35:46 2019 From: n4tl2 at yahoo.com (Tom Lewis) Date: Fri, 14 Jun 2019 19:35:46 +0000 (UTC) Subject: [Dxbase] sound References: <1786061945.1208538.1560540946075.ref@mail.yahoo.com> Message-ID: <1786061945.1208538.1560540946075@mail.yahoo.com> Hello Everyone, My sound announcements have stopped working. I click on the speaker on the bottom right of the main window and it does not change to green.? In user options, the master sound is off. I can't find where to run it on. Help. 73 Tom N4TL? From KL7TC at gci.net Wed Jun 19 02:34:01 2019 From: KL7TC at gci.net (Bill - KL7TC) Date: Tue, 18 Jun 2019 22:34:01 -0800 Subject: [Dxbase] Selection Wizard Issue...again Message-ID: <00.8C.11251.957D90D5@smtp01.beryl.bos.sync.lan> Trying to export my dad?s 2007 log to adif using the selection wizard. I have used it in the past on mine with no issues. 1. No checks blocks 2. Tried test first and no test, nothing happens. 3. When I click start, it opens the location and when hit ok, nothing happens. I was trying it at his house and mine with same result?nothing. There are 2373 qsos in the log. Not sure what the issue is?unless it?s a Windows 10 issue. Thanks and 73, Bill ? KL7TC Fairbanks, Alaska BP64DU Sent from Mail for Windows 10 From fred at g4bwp.com Wed Jun 19 03:32:23 2019 From: fred at g4bwp.com (Fred Handscombe) Date: Wed, 19 Jun 2019 07:32:23 +0000 Subject: [Dxbase] Selection Wizard Issue...again In-Reply-To: <00.8C.11251.957D90D5@smtp01.beryl.bos.sync.lan> References: <00.8C.11251.957D90D5@smtp01.beryl.bos.sync.lan> Message-ID: Bill Does the Opr Call in his log match the registered callsign? You can check in Help > About... That is the cause of many problems in DXbase I can confirm that the Selection Wizard with no tick marks in the QSO Filters page WILL export the entire log under Windows 10 73 Fred G4BWP www.g4bwp.com Hoarder of fine valved radios ------ Original Message ------ From: "Bill - KL7TC" To: "Dxbase at mailman.qth.net" Sent: 19/06/2019 07:34:01 Subject: [Dxbase] Selection Wizard Issue...again >Trying to export my dad?s 2007 log to adif using the selection wizard. I have used it in the past on mine with no issues. > >1. No checks blocks >2. Tried test first and no test, nothing happens. >3. When I click start, it opens the location and when hit ok, nothing happens. > >I was trying it at his house and mine with same result?nothing. There are 2373 qsos in the log. > >Not sure what the issue is?unless it?s a Windows 10 issue. > >Thanks and 73, >Bill ? KL7TC >Fairbanks, Alaska BP64DU > > >Sent from Mail for Windows 10 > >______________________________________________________________ >Dxbase mailing list >Home: http://mailman.qth.net/mailman/listinfo/dxbase >Help: http://mailman.qth.net/mmfaq.htm >Post: mailto:Dxbase at mailman.qth.net > >This list hosted by: http://www.qsl.net >Please help support this email list: http://www.qsl.net/donate.html From kl7tc at gci.net Wed Jun 19 10:02:11 2019 From: kl7tc at gci.net (Bill - KL7TC) Date: Wed, 19 Jun 2019 14:02:11 +0000 (UTC) Subject: [Dxbase] Selection Wizard Issue...again In-Reply-To: References: <00.8C.11251.957D90D5@smtp01.beryl.bos.sync.lan> Message-ID: <9C343A4D5E7C9508.5345BD78-0C28-4EA3-A1E7-4083CD18B332@mail.outlook.com> It is different On Tue, Jun 18, 2019 at 11:32 PM -0800, "Fred Handscombe" wrote: Bill Does the Opr Call in his log match the registered callsign? You can check in Help > About... That is the cause of many problems in DXbase I can confirm that the Selection Wizard with no tick marks in the QSO Filters page WILL export the entire log under Windows 10 73 Fred G4BWP www.g4bwp.com Hoarder of fine valved radios ------ Original Message ------ From: "Bill - KL7TC" To: "Dxbase at mailman.qth.net" Sent: 19/06/2019 07:34:01 Subject: [Dxbase] Selection Wizard Issue...again >Trying to export my dad?s 2007 log to adif using the selection wizard. I have used it in the past on mine with no issues. > >1. No checks blocks >2. Tried test first and no test, nothing happens. >3. When I click start, it opens the location and when hit ok, nothing happens. > >I was trying it at his house and mine with same result?nothing. There are 2373 qsos in the log. > >Not sure what the issue is?unless it?s a Windows 10 issue. > >Thanks and 73, >Bill ? KL7TC >Fairbanks, Alaska BP64DU > > >Sent from Mail for Windows 10 > >______________________________________________________________ >Dxbase mailing list >Home: http://mailman.qth.net/mailman/listinfo/dxbase >Help: http://mailman.qth.net/mmfaq.htm >Post: mailto:Dxbase at mailman.qth.net > >This list hosted by: http://www.qsl.net >Please help support this email list: http://www.qsl.net/donate.html From fred at g4bwp.com Wed Jun 19 10:58:31 2019 From: fred at g4bwp.com (Fred Handscombe) Date: Wed, 19 Jun 2019 14:58:31 +0000 Subject: [Dxbase] Selection Wizard Issue...again In-Reply-To: <9C343A4D5E7C9508.5345BD78-0C28-4EA3-A1E7-4083CD18B332@mail.outlook.com> References: <00.8C.11251.957D90D5@smtp01.beryl.bos.sync.lan> <9C343A4D5E7C9508.5345BD78-0C28-4EA3-A1E7-4083CD18B332@mail.outlook.com> Message-ID: If the Opr Call is not the registered one then DXbase will not export any contacts If you "find and replace" the Opr Call with the registered one through the whole log then it will work for you The registered Opr Call was Jack's original way of stopping bootleggers 73 Fred G4BWP www.g4bwp.com Hoarder of fine valved radios ------ Original Message ------ From: "Bill - KL7TC" To: "Fred Handscombe" ; dxbase at mailman.qth.net Sent: 19/06/2019 15:02:11 Subject: Re: [Dxbase] Selection Wizard Issue...again >It is different > > > > >On Tue, Jun 18, 2019 at 11:32 PM -0800, "Fred Handscombe" > wrote: > >>Bill >> >>Does the Opr Call in his log match the registered callsign? >> >>You can check in Help > About... >> >>That is the cause of many problems in DXbase >> >>I can confirm that the Selection Wizard with no tick marks in the QSO >>Filters page WILL export the entire log under Windows 10 >> >>73 Fred >>G4BWP >> >>www.g4bwp.com >>Hoarder of fine valved radios >> >>------ Original Message ------ >>From: "Bill - KL7TC" >>To: "Dxbase at mailman.qth.net" >>Sent: 19/06/2019 07:34:01 >>Subject: [Dxbase] Selection Wizard Issue...again >> >> >Trying to export my dad?s 2007 log to adif using the selection wizard. I have used it in the past on mine with no issues. >> > >> >1. No checks blocks >> >2. Tried test first and no test, nothing happens. >> >3. When I click start, it opens the location and when hit ok, nothing happens. >> > >> >I was trying it at his house and mine with same result?nothing. There are 2373 qsos in the log. >> > >> >Not sure what the issue is?unless it?s a Windows 10 issue. >> > >> >Thanks and 73, >> >Bill ? KL7TC >> >Fairbanks, Alaska BP64DU >> > >> > >> >Sent from Mail for Windows 10 >> > >> >______________________________________________________________ >> >Dxbase mailing list >> >Home: http://mailman.qth.net/mailman/listinfo/dxbase >> >Help: http://mailman.qth.net/mmfaq.htm >> >Post: mailto:Dxbase at mailman.qth.net >> > >> >This list hosted by: http://www.qsl.net >> >Please help support this email list: http://www.qsl.net/donate.html >> >> From kl7tc at gci.net Wed Jun 19 11:18:38 2019 From: kl7tc at gci.net (Bill - KL7TC) Date: Wed, 19 Jun 2019 15:18:38 +0000 (UTC) Subject: [Dxbase] Selection Wizard Issue...again In-Reply-To: References: <00.8C.11251.957D90D5@smtp01.beryl.bos.sync.lan> <9C343A4D5E7C9508.5345BD78-0C28-4EA3-A1E7-4083CD18B332@mail.outlook.com> Message-ID: <9C343A4D5E7C9508.432AF85F-3C51-4CB6-BB3D-F5ED5066A624@mail.outlook.com> Well that's lame because what happens if you had 2 callsigns? On Wed, Jun 19, 2019 at 6:58 AM -0800, "Fred Handscombe" wrote: If the Opr Call is not the registered one then DXbase will not export any contacts If you "find and replace" the Opr Call with the registered one through the whole log then it will work for you The registered Opr Call was Jack's original way of stopping bootleggers 73 Fred G4BWP www.g4bwp.com Hoarder of fine valved radios ------ Original Message ------ From: "Bill - KL7TC" To: "Fred Handscombe" ; dxbase at mailman.qth.net Sent: 19/06/2019 15:02:11 Subject: Re: [Dxbase] Selection Wizard Issue...again >It is different > > > > >On Tue, Jun 18, 2019 at 11:32 PM -0800, "Fred Handscombe" > wrote: > >>Bill >> >>Does the Opr Call in his log match the registered callsign? >> >>You can check in Help > About... >> >>That is the cause of many problems in DXbase >> >>I can confirm that the Selection Wizard with no tick marks in the QSO >>Filters page WILL export the entire log under Windows 10 >> >>73 Fred >>G4BWP >> >>www.g4bwp.com >>Hoarder of fine valved radios >> >>------ Original Message ------ >>From: "Bill - KL7TC" >>To: "Dxbase at mailman.qth.net" >>Sent: 19/06/2019 07:34:01 >>Subject: [Dxbase] Selection Wizard Issue...again >> >> >Trying to export my dad?s 2007 log to adif using the selection wizard. I have used it in the past on mine with no issues. >> > >> >1. No checks blocks >> >2. Tried test first and no test, nothing happens. >> >3. When I click start, it opens the location and when hit ok, nothing happens. >> > >> >I was trying it at his house and mine with same result?nothing. There are 2373 qsos in the log. >> > >> >Not sure what the issue is?unless it?s a Windows 10 issue. >> > >> >Thanks and 73, >> >Bill ? KL7TC >> >Fairbanks, Alaska BP64DU >> > >> > >> >Sent from Mail for Windows 10 >> > >> >______________________________________________________________ >> >Dxbase mailing list >> >Home: http://mailman.qth.net/mailman/listinfo/dxbase >> >Help: http://mailman.qth.net/mmfaq.htm >> >Post: mailto:Dxbase at mailman.qth.net >> > >> >This list hosted by: http://www.qsl.net >> >Please help support this email list: http://www.qsl.net/donate.html >> >> From fred at g4bwp.com Wed Jun 19 11:43:51 2019 From: fred at g4bwp.com (Fred Handscombe) Date: Wed, 19 Jun 2019 15:43:51 +0000 Subject: [Dxbase] Selection Wizard Issue...again In-Reply-To: <9C343A4D5E7C9508.432AF85F-3C51-4CB6-BB3D-F5ED5066A624@mail.outlook.com> References: <00.8C.11251.957D90D5@smtp01.beryl.bos.sync.lan> <9C343A4D5E7C9508.5345BD78-0C28-4EA3-A1E7-4083CD18B332@mail.outlook.com> <9C343A4D5E7C9508.432AF85F-3C51-4CB6-BB3D-F5ED5066A624@mail.outlook.com> Message-ID: You have to get a new registration file with ALL the callsigns in it, or just put the registered call in the field as it serves no other purpose anyway, you need 1 log file per on the air callsign. I have one with 5 or 6 of my personal calls in various countries I had many robust discussions with Jack on the subject but he wouldn?t budge! 73 Fred G4BWP www.g4bwp.com Hoarder of fine valved radios ------ Original Message ------ From: "Bill - KL7TC" To: "Fred Handscombe" ; dxbase at mailman.qth.net Sent: 19/06/2019 16:18:38 Subject: Re: Re[2]: [Dxbase] Selection Wizard Issue...again >Well that's lame because what happens if you had 2 callsigns? > > > > >On Wed, Jun 19, 2019 at 6:58 AM -0800, "Fred Handscombe" > wrote: > >>If the Opr Call is not the registered one then DXbase will not export >>any contacts >> >>If you "find and replace" the Opr Call with the registered one through >>the whole log then it will work for you >> >>The registered Opr Call was Jack's original way of stopping bootleggers >> >>73 Fred >>G4BWP >> >>www.g4bwp.com >>Hoarder of fine valved radios >> >>------ Original Message ------ >>From: "Bill - KL7TC" >>To: "Fred Handscombe" ; dxbase at mailman.qth.net >>Sent: 19/06/2019 15:02:11 >>Subject: Re: [Dxbase] Selection Wizard Issue...again >> >> >It is different >> > >> > >> > >> > >> >On Tue, Jun 18, 2019 at 11:32 PM -0800, "Fred Handscombe" >> > wrote: >> > >> >>Bill >> >> >> >>Does the Opr Call in his log match the registered callsign? >> >> >> >>You can check in Help > About... >> >> >> >>That is the cause of many problems in DXbase >> >> >> >>I can confirm that the Selection Wizard with no tick marks in the QSO >> >>Filters page WILL export the entire log under Windows 10 >> >> >> >>73 Fred >> >>G4BWP >> >> >> >>www.g4bwp.com >> >>Hoarder of fine valved radios >> >> >> >>------ Original Message ------ >> >>From: "Bill - KL7TC" >> >>To: "Dxbase at mailman.qth.net" >> >>Sent: 19/06/2019 07:34:01 >> >>Subject: [Dxbase] Selection Wizard Issue...again >> >> >> >> >Trying to export my dad?s 2007 log to adif using the selection wizard. I have used it in the past on mine with no issues. >> >> > >> >> >1. No checks blocks >> >> >2. Tried test first and no test, nothing happens. >> >> >3. When I click start, it opens the location and when hit ok, nothing happens. >> >> > >> >> >I was trying it at his house and mine with same result?nothing. There are 2373 qsos in the log. >> >> > >> >> >Not sure what the issue is?unless it?s a Windows 10 issue. >> >> > >> >> >Thanks and 73, >> >> >Bill ? KL7TC >> >> >Fairbanks, Alaska BP64DU >> >> > >> >> > >> >> >Sent from Mail for Windows 10 >> >> > >> >> >______________________________________________________________ >> >> >Dxbase mailing list >> >> >Home: http://mailman.qth.net/mailman/listinfo/dxbase >> >> >Help: http://mailman.qth.net/mmfaq.htm >> >> >Post: mailto:Dxbase at mailman.qth.net >> >> > >> >> >This list hosted by: http://www.qsl.net >> >> >Please help support this email list: http://www.qsl.net/donate.html >> >> >> >> >> >> From kl7tc at gci.net Wed Jun 19 12:14:16 2019 From: kl7tc at gci.net (Bill - KL7TC) Date: Wed, 19 Jun 2019 16:14:16 +0000 (UTC) Subject: [Dxbase] Selection Wizard Issue...again In-Reply-To: References: <00.8C.11251.957D90D5@smtp01.beryl.bos.sync.lan> <9C343A4D5E7C9508.5345BD78-0C28-4EA3-A1E7-4083CD18B332@mail.outlook.com> <9C343A4D5E7C9508.432AF85F-3C51-4CB6-BB3D-F5ED5066A624@mail.outlook.com> Message-ID: <9C343A4D5E7C9508.18C6C4ED-17F0-4E83-B930-EE77C0F7DC80@mail.outlook.com> Thanks Fred! What a PITA. On Wed, Jun 19, 2019 at 7:43 AM -0800, "Fred Handscombe" wrote: You have to get a new registration file with ALL the callsigns in it, or just put the registered call in the field as it serves no other purpose anyway, you need 1 log file per on the air callsign. I have one with 5 or 6 of my personal calls in various countries I had many robust discussions with Jack on the subject but he wouldn?t budge! 73 Fred G4BWP www.g4bwp.com Hoarder of fine valved radios ------ Original Message ------ From: "Bill - KL7TC" To: "Fred Handscombe" ; dxbase at mailman.qth.net Sent: 19/06/2019 16:18:38 Subject: Re: Re[2]: [Dxbase] Selection Wizard Issue...again >Well that's lame because what happens if you had 2 callsigns? > > > > >On Wed, Jun 19, 2019 at 6:58 AM -0800, "Fred Handscombe" > wrote: > >>If the Opr Call is not the registered one then DXbase will not export >>any contacts >> >>If you "find and replace" the Opr Call with the registered one through >>the whole log then it will work for you >> >>The registered Opr Call was Jack's original way of stopping bootleggers >> >>73 Fred >>G4BWP >> >>www.g4bwp.com >>Hoarder of fine valved radios >> >>------ Original Message ------ >>From: "Bill - KL7TC" >>To: "Fred Handscombe" ; dxbase at mailman.qth.net >>Sent: 19/06/2019 15:02:11 >>Subject: Re: [Dxbase] Selection Wizard Issue...again >> >> >It is different >> > >> > >> > >> > >> >On Tue, Jun 18, 2019 at 11:32 PM -0800, "Fred Handscombe" >> > wrote: >> > >> >>Bill >> >> >> >>Does the Opr Call in his log match the registered callsign? >> >> >> >>You can check in Help > About... >> >> >> >>That is the cause of many problems in DXbase >> >> >> >>I can confirm that the Selection Wizard with no tick marks in the QSO >> >>Filters page WILL export the entire log under Windows 10 >> >> >> >>73 Fred >> >>G4BWP >> >> >> >>www.g4bwp.com >> >>Hoarder of fine valved radios >> >> >> >>------ Original Message ------ >> >>From: "Bill - KL7TC" >> >>To: "Dxbase at mailman.qth.net" >> >>Sent: 19/06/2019 07:34:01 >> >>Subject: [Dxbase] Selection Wizard Issue...again >> >> >> >> >Trying to export my dad?s 2007 log to adif using the selection wizard. I have used it in the past on mine with no issues. >> >> > >> >> >1. No checks blocks >> >> >2. Tried test first and no test, nothing happens. >> >> >3. When I click start, it opens the location and when hit ok, nothing happens. >> >> > >> >> >I was trying it at his house and mine with same result?nothing. There are 2373 qsos in the log. >> >> > >> >> >Not sure what the issue is?unless it?s a Windows 10 issue. >> >> > >> >> >Thanks and 73, >> >> >Bill ? KL7TC >> >> >Fairbanks, Alaska BP64DU >> >> > >> >> > >> >> >Sent from Mail for Windows 10 >> >> > >> >> >______________________________________________________________ >> >> >Dxbase mailing list >> >> >Home: http://mailman.qth.net/mailman/listinfo/dxbase >> >> >Help: http://mailman.qth.net/mmfaq.htm >> >> >Post: mailto:Dxbase at mailman.qth.net >> >> > >> >> >This list hosted by: http://www.qsl.net >> >> >Please help support this email list: http://www.qsl.net/donate.html >> >> >> >> >> >> From wa6axe at verizon.net Fri Jun 28 14:06:12 2019 From: wa6axe at verizon.net (Joseph Glockner) Date: Fri, 28 Jun 2019 18:06:12 +0000 (UTC) Subject: [Dxbase] For IOTA users -- New IOTA references References: <1455546351.364387.1561745172286.ref@mail.yahoo.com> Message-ID: <1455546351.364387.1561745172286@mail.yahoo.com> Just found out that there are 6 NEW IOTA References: https://iota-world.org/info/new_groups_2019.pdf | Announcement of New IOTA Groups at Ham Radio Friedrichshafen on 22 June 2019 - iota-world.orgAnnouncement of New IOTA Groups at Ham Radio Friedrichshafen on 22 June 2019 Following the decision to split the 5 yearly review of the IOTA list into two parts, we announced the first tranche ofiota-world.org | Passing along as FYI!! 73 Joe WA6AXE