[Dxbase] Kenwood TS950SDX Radio Control

[Chris Poulson]

Thanks Tony,

I had already changed the pacing and eoc  to lower values, I have now
changed them to your suggested values and it may be a little quicker
now, but there is STILL a BIG BIG  difference in speed between
pressing Alt R and QSY'ing by clicking on a DX Spot.

I also have a TS2000 and that does not exhibit the same problem, even
without changing the Radios.ini there is not any noticeable difference
between the 2 QSY'ing methods. With the TS950 the difference is very
noticeable!.

I realise that it will never be as quick as the TS2000 due to the
relatively low bps rate of the TS950 (4800bps) but it has me beat why
is SO FAST when pressing Alt R, its almost instant!.

73's de G4PZN (ßarney)
 

On Sun, 9 Oct 2005 00:00:57 -0400, you wrote:

>Try changing these setting in the TS-940 portion of the Radio.ini file
>The suggestions below are what I use with the TS-2000 and it works FAST
>and GREAT.
>
>PACING is now set to 50 change to 1
>
>In all the entries below where the eoc is anything other than 0,
>change them to eoc( 0 )
>
>SelectVFOA= eoc(0)
>SetVFOA= asc( "FA" ) dec( %vfoa,11 ) asc( ";" ) eoc( 200 )
>GetVFOA= asc("FA;") rrs(14) eoc( 200 )
>PrsVFOA= asc("FA") dec(%vfoa,11) asc(";") eoc(0)
>
>SelectVFOB= eoc( 200 )
>SetVFOB= asc( "FB" ) dec( %vfob,11 ) asc( ";" ) eoc( 200 )
>GetVFOB= asc("FB;") rrs(14) eoc( 200 )
>PrsVFOB= asc("FB") dec(%vfob,11) asc(";") eoc(0)
>
>SetMode= asc("MD") dec( %mode, 1 ) asc ( ";" ) eoc( 200 )
>GetMode=  asc( "IF;" ) rrs(38) eoc( 0 )
>PrsMode= asc("IF") dec(%dummy,11) dec(%dummy,10) dec(%dummy,6) dec(%mode,1) 
>dec(%dummy,1) dec(%dummy,1) dec(%dummy,1) dec(%dummy,4) asc(";") eoc(0)
>
>SetFilter= asc( "VB" ) dec( %filter, 2 ) asc ( ";" ) eoc( 0 )
>GetFilter= asc( "VB;" ) eoc( 0 )
>PrsFilter= asc("VB")  dec( %filter, 2 ) asc ( ";" ) eoc( 0 )
>
>SetSplit= asc( "SP" ) dec( %split ) asc ( ";" ) eoc( 0 )
>GetSplit= asc( "IF;" ) rrs(38) eoc( 0 )
>PrsSplit= asc("IF") dec(%dummy,30) dec(%split,1) dec(%dummy,4) asc(";") 
>eoc(0)
>
>73 de Tony, KD4K
>My Radio web site
>http://kd4k.no-ip.info/kd4k/radio.html
>My Weather Web Site
>http://kd4k.no-ip.info
>Sawnee Mountain Repeater Web Site
>http://www.sawneemtn.org/
>
>----- Original Message ----- 
>From: "Chris Poulson" <pencom at scootmail.com>
>To: <dxbase at mailman.qth.net>
>Sent: Saturday, October 08, 2005 3:29 PM
>Subject: [Dxbase] Kenwood TS950SDX Radio Control
>
>
>If I click on a DX spot, it takes a good second or more before the
>radio reponds, however, if I then do an Alt R (Reset HF Frequency) the
>radio resonds WITHOUT ANY noticeable delay!.
>
>As it QSY's instantly when pressing Alt R It would appear that it is
>nothing to do with the COM port speed and probably more to do with the
>Radio.ini perhaps?.
>
>Is the something I could edit in the Radios.ini that will make the
>radio more reponsive when I QSY by clicking on a DX Spot?.
>If it was as quick as ALT R it would be fantastic :-)
>
>73's de G4PZN (ßarney)
>
>Chris Poulson
>
>______________________________________________________________
>Dxbase mailing list
>Home: http://mailman.qth.net/mailman/listinfo/dxbase
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:Dxbase at mailman.qth.net