[Dx4win] PSK31 - how to transmit?

[Mel]

The ACC connector in the rear. It is the same connector for every Icom
rig I have ever used: pin 3, ACC 1 (Pin 3, ACC 2 would also work).

Actually... that's not strictly true... the really old Icoms used a 24
pin accessory connector... but I used an adapter to simulate the two ACC
plugs with my 751A so I was sill using pin 3 ;-)

David M. Monfried wrote:
> Mel,
> 
> Thank you. May I ask a follow-up question, then? I assume you control the
> 7700 via another com port, which is connected to the rig's RS232 jack,
> right? If so, where does the second com port line, used for PTT, plug into
> the 7700? In my case, my single RS232 is used for rig control and the remote
> jack is used to control the SteppIr antenna.
> 
> I think I'm getting close here, but there's something very obvious - and
> very simple - that's missing!
> 
> 73,
> Dave
> 
> -----Original Message-----
> From: Mel [mailto:ve2dc at videotron.ca] 
> Sent: Tuesday, January 12, 2010 9:10 AM
> To: David M. Monfried; DX4WIN
> Subject: Re: [Dx4win] PSK31 - how to transmit?
> 
> I use a COM port to control PTT with my 7700. It is the same setup I 
> used with my older IC781. Newer Icoms like the 7700 and 7800 can switch 
> to transmit under software control via the CI-V bus but I don't think 
> D4W supports it yet... or if it does, I don't know how to make it work.
> 
> David M. Monfried wrote:
>> Searched the archives but could not find the answer to this simple(?)
>> problem - I'm unable to key the IC7800 using the PSK31 function in DX4WIN
>> 7.05.04. I am able to decode signals, but can't figure out what I'm doing
>> wrong on transmit. Here's the set-up:
>>
>>  
>>
>> IC7800 + Navigator (in file/Preferences/Control, tried both Default Sound
>> Card and Cards 0 and 1 in PSK Sound Card).
>>
>>  
>>
>> Presently control radio via com port 7; tried Stop Radio and using com
> port
>> 7 ( PSK31 window/ Alt+S /TX/com 7, then tried PTT and VOX).  Nothing.
>>
>>  
>>
>> Control SteppIr antenna via Remote jack on IC7800.  
>>
>>  
>>
>> Successfully use HRD with DM780 - but give up DX4WIN control of rig to HRD
>> when I want to operate RTTY or PSK31.that's why I'd like to get the PSK31
>> function going on DX4WIN.
>>
>>  
>>
>> I assume I'm missing something elementary - a cable connection or software
>> setting. If I have to add a PTT connection, I don't see where it would
>> terminate on the radio.
>>
>>  
>>
>> Any help would be much appreciated. Thank you.
>>
>>  
>>
>> Dave, W2PK
>>
>>  
>>
>>  
>>
>>  
>>
>>  
>>
>>  
>>
>>  
>>
>> ______________________________________________________________
>> Dx4win mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/dx4win
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Dx4win at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>>
> 
> 
>