[Dx4win] Print bureau labels

[OZ1AXG Flam]

Hi

my 2€  ... from Dx4Win I print labels to a PDF file that i save (i have 
installed a PDF "printer").

Then i use this PDF file for the actual label print.
I can re-print any pages and i also have the PDF file as documentation later 
of that i can check if in doubt.

--
OZ1AXG Flam


----- Original Message ----- 
From: "John Shaw" <jnshaw at internet.co.nz>
To: <dx4win at mailman.qth.net>
Sent: Wednesday, July 22, 2009 10:07 PM
Subject: Re: [Dx4win] Print bureau labels


> Hi Hamad,
>
> If you want to break your QSL print job into smaller lots for safety a
> better way is to use the range option when you go to print.  This gives 
> you
> a lot more control of the size of each print job and the ability to 
> recover
> with less wastage if the printer jambs or something.
>
> First rule; make a backup before you start.
>
> Second: Don't ever say yes to changing the print flags until you are
> completely satisfied you have all your cards printed.
>
> Example: say you have 2000 cards to print, you can break this up into 20
> lots of 100, use ranges 1-100, 101-200 etc.  Write these out on paper 
> before
> you start so you can cross them off as each is completed.
>
> Don't ever say yes to changing the print flags until you are completely
> satisfied you have all your cards printed.
>
> If your printer breaks down during a print you can do that range again, 
> but
> first print to screen and scroll through to find the last good label
> printed, then make a note of the page number and make a new range to
> complete all after that page to the end of the current range to paper. 
> This
> works very well when printing direct on cards as each page is one card so
> you get very little wastage if you printer fails during a print.
>
> If you don't change the print flags you can resume printing at any time if
> you keep a record of where you left off.
>
> I hope that helps and makes sense.
>
> 73 John ZL1BYZ.
>
> -----Original Message-----
> From: dx4win-bounces at mailman.qth.net 
> [mailto:dx4win-bounces at mailman.qth.net]
> On Behalf Of Hamad 9K2HN
> Sent: Wednesday, 22 July 2009 8:07 p.m.
> To: dx4win
> Subject: [Dx4win] Print bureau labels
>
> Hi,
>
>   I do have a question is there a way which I can print bureau labels for 
> a
> specific country? I do have more than 2000 bureau labels to print, and to
> print them all together will take very long time (i'm printing directly on
> the qsl card) so i thought it will be better if i can specify a country to
> print for. any Idea?
>
> de 9k2hn
> Hamad
> ______________________________________________________________
> Dx4win mailing list
> Home: http://mailman.qth.net/mailman/listinfo/dx4win
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Dx4win at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>
>
> ______________________________________________________________
> Dx4win mailing list
> Home: http://mailman.qth.net/mailman/listinfo/dx4win
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Dx4win at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>


--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.392 / Virus Database: 270.13.25/2256 - Release Date: 07/23/09 
06:02:00