[Dx4win] YAESU FTDX9000 and Also FT2000 cat problems

[ON4AOI]

Ok Toby,
Tnx for your input 

Is it possible to check what firmware version is in the FT2000 ?
And also can you pse connect the radio directly to the PC
Without Microham interface.
 

73 Guy ON4AOI

BAND DECODER and related stuff at

http://www.on4aoi.be/banddecoder.htm

DX4WIN soft and related stuff at

http://www.on4aoi.be/dx4win.htm

DX4WIN, WRITELOG, WF1B & RITTY CW & RTTY interfaces at

 http://www.on4aoi.be/keyer.htm

ARSWIN link and related stuff at

http://www.on4aoi.be/web7.htm

DXTELNET soft and related stuff at

http://www.on4aoi.be/dxt.htm


-----Original Message-----
From: Toby & Ira Stoler [mailto:stoler at erols.com] 
Sent: Saturday, September 02, 2006 10:37 PM
To: ON4AOI
Cc: w9rpm at centurytel.net; Dx4win at mailman.qth.net
Subject: Re: [Dx4win] YAESU FTDX9000 and Also FT2000 cat problems

Hello Guy and everyone,

I received my FT2000 from Texas Towers yesterday.  I was their number 2 
FT2000 sold.

I have tried using FT9K driver in DX4WIN 7.02 and it does follow the 
radio band changes and successfully read frequency into qso record.  It 
does not follow when I click on packet spots.

I am also using Writelog version 10.59D, also using FT9K driver.  WL 
seems to work properly both in reading frequency and mode from radio as 
well as setting VFO A and B when the spot specifies a split frequency 
and only VFO A for simplex spots.

I am also using MicroHam Microkeyer USB interface with their version 
3.1.4 router and it is properly sensing FT2000 frequency using settings 
for FT9K.

I hope this is useful information.

73,

Ira K2RD

ON4AOI wrote:

>John,
>
>Dx4win is supporting the FTDX9000 but it isn't working
>Like in All OTHER LOGBOOK or CONTESTPRG correct.
>OMS, PY5EG explained clearly what the problem is.
>
>"Changing bands manually on the FT9K"
>DX4WIN follows to the correct band.
>This works OK.
>
>"Sending a grabbed spot to the radio."
>The radio goes to the correct frequency on the FT9K 
>But it goes to VFO B for XMIT and not to VFO A,
>independently if the station is operating split or not.
>Cmd for VFO A = FA...... and cmd for VFO B = FB...... etc
>This is done by all tested programs but the problem stays
>For all the same. 
>  
>Probably this is a FIRMWARE bug in the FT9K but nobody answers this !!! 
>
>Maybe this is also the reason why you can't buy the FT2000 
>( = same new CAT commands like FTDX9000D).
>There are some sold in USA but nobody knows (mailed several big dealers all
>over the world) when they will be available again. 
>
> 
>
>73 Guy ON4AOI
>
>BAND DECODER and related stuff at
>
>http://www.on4aoi.be/banddecoder.htm
>
>DX4WIN soft and related stuff at
>
>http://www.on4aoi.be/dx4win.htm
>
>DX4WIN, WRITELOG, WF1B & RITTY CW & RTTY interfaces at
>
> http://www.on4aoi.be/keyer.htm
>
>ARSWIN link and related stuff at
>
>http://www.on4aoi.be/web7.htm
>
>DXTELNET soft and related stuff at
>
>http://www.on4aoi.be/dxt.htm
>
>
>
>_______________________________________________
>Dx4win mailing list
>Dx4win at mailman.qth.net
>http://mailman.qth.net/mailman/listinfo/dx4win
>  
>