[Dx4win] QSX Function of TS-850S

Mon, 25 Mar 2002 17:05:55 -0600

I disagree! My Kenwood TS940 is put into split mode any time the qsx freq is
included with the spot and is selected.  The only thing I have had to get
used to was making the correct selection when listening.  If I simply right
click on a spot and select listen, then the radio goes instead to the spot
that was highlighted.  I have to left click first to highlight the spot I
want and then right click to listen.  If it is a split operation and is
spotted properly with a freq in the QSX window, the radio works correctly
and comes up in split mode as it should.  If this is confusing to you don't
be alarmed.  I just got confused myself trying to explain it! :)

 J Sartain  KC4ALG
[email protected]
http://www.heartoftn.net/users/jsartain/KC4ALG.htm

----- Original Message -----
From: "Dean M. St. Hill" <[email protected]>
To: "Mike Rhodes" <[email protected]>; <[email protected]>
Sent: Monday, March 25, 2002 10:26 AM
Subject: Re: [Dx4win] QSX Function of TS-850S

> I have used several Kenwoods with varius logging programmes and this is
how
> it is implemented. The software puts the frequencies into the two VFO's
and
> then you have to manually place the rig into split with the appropriate
> button depending on the specific transceiver.
>
> There is simply no command available (at least up to the TS-850) for
putting
> the rig into split mode.
>
>
> 73, and have fun.
>
> Dean - 8P6SH
> ----- Original Message -----
> From: "Mike Rhodes" <[email protected]>
> To: <[email protected]>
> Sent: Monday, March 25, 2002 11:26 AM
> Subject: Re: [Dx4win] QSX Function of TS-850S
>
>
> > Tim,
> >   My 850 behaves the same but this is the only radio-enabled logging
> program
> > I have used since I bought the rig so I assumed it is the typical
> response.
> > The QSX frerquency is loaded but you have to hit the 'TX-B' button to
get
> > into split mode.
> >
> > Mike / W8DN
> > DX4Win Since Ver 0.97
> >
> > ----- Original Message -----
> > From: "Timothy Coker" <[email protected]>
> > To: <[email protected]>
> > Sent: Sunday, March 24, 2002 11:11 PM
> > Subject: [Dx4win] QSX Function of TS-850S
> >
> >
> > Hi, I cannot seem to get my TS-850S to QSX properly with spots. My radio
> > would do it no problem using Log Windows when I used to use their
software
> > so I know my cable's pins should be configured properly. I can QSY with
> > correct mode to a spot without problem, but no matter the method of
> listing
> > QSX/up or whatever on a spot it will not work. I am using the Kenwood
> > 850-950 setting. Here is what happens... I double click with mouse on a
> spot
> > that has Up 'x' or QSX frequency listed, my radio QSY's there, the radio
> is
> > actually setup properly for QSX frequency (RX VFO A, TX VFO B) but then
is
> > immediately switched back to RX/TX on VFO A. It will not stay on split
VFO
> > operation. I've played with the different options in DX4WIN and have
> looked
> > through the user manual, any suggestions please?
> >
> > Timothy Coker - N6WIN
> > Private Pilot - Instrument
> >
> >
> > _______________________________________________
> > Dx4win mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/dx4win
> >
> > _______________________________________________
> > Dx4win mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/dx4win
> >
> >
> >
> > [Virus scanned by SunBeach - http://www.sunbeach.net]
> >
> >
>
>
>
>
> [Virus scanned by SunBeach - http://www.sunbeach.net]
>
> _______________________________________________
> Dx4win mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/dx4win