[DCboatanchors] Mics, speech processor, filters, and much more FS

[Ken Simpson, W8EK]

Extensive List of Many Ham Items For Sale
2 meter FM Rig, TenTec Items, Microphones, TVI filters,
Wattmeter, HT accessories, Speaker, Phone Patches, and
much more


Two meter FM Transceiver:

Azden PCS-4000 FM transceiver for 2 meters

This is a nice small unit, which has 16 memories in 2 banks,
scan capabilities (memories or band scan), priority channel,
DTMF touchtone microphone with Up and Down switch and
Memory 1 call, plus all sorts of other bells and whistles. It has
25 Watts or 5 Watts output power and an extremely good
receiver.

This particular unit works fine, and looks very nice.

Microphone, mobile bracket, power cord, and manual are
included for $70.


VoMax Speech Processor:

This unit was considered the absolute best speech processor
available in the 80's. The VoMax splits the audio signal into
discrete bands, processes each band, passes the separate
signals through bandpass filters to eliminate distortion,
and sums the signals in a phase-equalizing combiner. The
result is superb audio you can feed to your transmitter
that has low distortion and 10-12db power gain!

The VoMax added between your microphone and transmitter
gives you extra punch that is equivalent to adding a linear
amplifier. It is power by 12 V DC at about 100 ma.

This particular unit works fine, and looks very nice.
Paper work is included for $75.


Communications Speaker
This 4 inch square speaker is optimized for communications
frequencies (300 to 3000 Hz). It is a Realistic Radio Shack
speaker in a black enclosure, and is an 8 ohm speaker. It
has a cord with a 1/8 inch (3.5 mm) mono plug on the end.
This one works fine and looks OK also. $15


Low Pass TVI Filters:

A low pass TVI filter is added to the transmitter (inserted
in the coax line after the transmitter or transceiver) to
reduce harmonic interference.

Drake TV-5200-LP
This is the more modern version of the Drake TV-1000 Low Pass
Filter. This is the filter that may also be used on the low
end of six meters, as well as HF. It is good for 1000 Watts
average below 30 MHz, and about 200 W up to 52 MHz. It works
fine, and is in very nice shape. $35

Drake TV-3300-LP Low Pass Filter
This is a modern low pass filter to go between your transmitter
and antenna, and has been optimized to have more attenuation
in the 40 MHz region, where many TVs have their IF. It is good
for 1000 Watts "average" according to the manual, and has
over 80 db attenuation at 41 MHz. This one looks great, and
includes the paper work. $30

B & W FL-10/1500 (Formerly known as model 425) low pass filter
B & W TVI filter, 50 ohm. It cuts off just above 10 meters,
and will handle 1500 Watts. SO-239 connector on each
end. This is the latest model B & W filter. It is in very nice
condition; it looks very close to new. With paper work $40.


TenTec Items:

TenTec Model 280 power supply, 20 amps at 13 V DC.
This supply is quite heavy duty electrically.
It has 2 pass transistors, instead of the one that
some have. It also has an ammeter on it.
This one works fine, and looks OK as well.
A previous owner removed the molded in TenTec power
cable on the back and added very heavy binding posts,
so that it can be used with many different rigs and
not just TenTec. It also has a couple RCA jacks for
lower power use.
With paper work for $100.

"Switcher / 25" 25 amp switching power supply
This is a 25 amp switching power supply in a case that
matches the early Omni series case, with the metal bezel
around it. It is in a case that is the same size as a 243
remote VFO. It has an ammeter on the front, along with
Switch, TenTec logo, and output bulb. The front panel
basically looks like a 280 power supply with a metal bezel,
but says "Switcher/25" on it. It is very quiet, and well
shielded, and does not produce any electrical noise that
I could find. $150


Microphones:

Heath High Impedance Hand Microphone
This is the black colored hand mic that was used on
the HW and SB series transceivers from 25 or 30 years ago.
It is a Hi Z mic. This particular mic is in good condition.
It works great, and looks fine cosmetically. It even includes
the mounting clip (which looks like it was never used).
This mic presently has stripped and tinned ends, but of
course a connector can easily be added.
I have paper work for a Heath GH-12 A hand microphone with
it, but am not certain that is what it is. My memory says
the GH-12 A was dark green in color, and this one is a
black color. $30

Shure 104 C, Low Z hand Microphone
This is a very heavy duty Shure mic. It appears to be new,
with stripped and tinned ends that have never been on a
connector. It is in its original box, with the original
instruction manual. $30

Generic Hand Microphone
This is a low impedance hand microphone, black in color.
It is presently has an 8 pin round connector, wired for
Kenwood. $25
As above, with no connector. $22

Regular hand microphone
Electret Condenser microphone
Generic Black mic, with gray PTT bar. Requires polarizing
voltage. $25

Lafayette EAM-15 dynamic hand microphone
2000 ohm impedance can be used any place a dynamic mic is needed.
Stripped and tinned leads.
It works fine, and looks good also. $25


DTMF Touch Tone Microphones:

Kenwood MC-48, DTMF Touch Tone Microphone
Round, 8 pin connector, will go with any Kenwood rig taking
this kind of connector (TM-201, TM-211, TM-221, TM-231,
TM-241, TM-2530, TS-50, TS-430, TS-440, TS-570, TS-850, TS-870,
TS-930, TS-940, TS-950, TW-4000, etc.).  Has UP and DOWN
switches and PTT, along with 16 digit touch tone pad.
It works fine, and includes paper work for $50.

Kenwood MC-46 DTMF Touch Tone Microphone
Touch tone DTMF microphone with 6 pin connector, as used on
TR-7730, TR-7800, TR-7850, TR-7930, TR-7950, TR-8400, TR-9000,
TR-9130, and others.  Up-down switch on top.  16 digit touch
tone pad. This one works fine, and includes paper work for $45.

CES 655 L "Microdialer" DTMF Microphone
You can manual dial a number, or automatically have it
stored in the mic, and "speed dial" with this mic. 12
digit touch tone pad on the front, with the microphone
part above the pad. This one presently has a 4 pin plug
on it, but of course that can be changed. $35

CES 600 L, Universal DTMF microphone
This has a normal touch tone pad on the front, with
a low impedance microphone. This one has the 8 pin
modular plug (like a computer LAN) on it. This mic has
not been used, so it is in really great condition.
With paper work for $40.

Data Signal "Data-Coder 5" touch tone mic
This mic has a 12 digit touchtone pad on it, plus a
normal low impedance microphone. With 4 pin plug.
Like new. $38


Speaker Microphones:

Azden SDX-316
This is the rounder style speaker mic that fits nicely in
the palm of your hand. Has 3.5 mm and 2.5 mm plugs for
Azden, Icom, some Yaesu, and others. $ 20

Kenwood SMC-24 speaker microphone
Fits Kenwood TR-2400 HT and others. This one looks fine
and works fine. $18


Kenwood MB-4000 Mobile Bracket
This mobile bracket is made to be used with the Kenwood
TW-4000 dual band transceiver, and possibly other rigs
as well.
This one is in good shape, with the paper work and hardware.
$15

ParaDynamics PDC-5 Wattmeter/Antenna Tuner
This unit has a wattmeter with scales of 100 W, 10 W, and
1 W. It has an SWR Bridge built in, with an antenna tuner.
It was obviously made for 11 meter use, but it works well
on other frequencies. The tuner portion works fine on 10 m,
12 m, and 15 m. The wattmeter seems accurate from 20 meters
thru 10 meters.
It is physically small (only 5 X 3 X 1), so would be ideal
for portable use.
The wattmeter and antenna tuner portion work fine, however,
the SWR portion of this unit is inoperative. It looks fine. $12


Hustler HF mobile antennas:

All work fine and are in good condition.

Standard" Hustler resonators (good for 400 Watts PEP):
75 meter resonator RM-75 $22

"Super" high power resonators (good for 2 KW PEP):
80 meter RM-80 S
can be cut for CW or phone, and also used on a 4BTV
Vertical to give 80/75 meter coverage $38


Heavy Duty Mobile/Portable Antenna Mount:

This is a very heavy duty antenna mount, designed to
take any standard 3/8-24 threaded antenna. which includes just
about any HF antenna and many other antennas as well.

The mount is made to be clamped around a vertical object, such
as a pipe, tubing, or even a square channel. It would be ideal
to attach to something like a chain link fence. It could also be
used as a mirror mount on trucks. It will take up to 1 1/2 inch
diameter objects. It has a very large screw type mechanism with
a large handle to tighten to the vertical object. It could be
placed in operation very quickly, so it is great for portable
and emergency operation, where one would want to set up a
mount quickly.

The bottom of it has an SO-239 connector, ready to take a
standard PL-259 connector.

This unit is in good condition. $20


HT accessories:

Icom BP-20 Battery Case For Sale:
The BP-20 is an "empty" battery pack designed to hold
regular AA cells. Of course a person can use regular
alkaline batteries, or NiCads, or NiMh batteries. This
pack will work with the Icom u2AT, u3AT, u4AT, and maybe
others. It is ideal if you have one of these HTs that
now has a dead battery.
This particular BP-20 is in its original box, and appears
to be new and never used. The box is labeled CM-20, which
is the same as the BP-20, except the commercial version.
$20

Lithium battery for Yaesu VX-2 or VX-3 HTs
Spare Lithium Ion battery pack for Yaesu VX-2 or VX-3.
It fits the new VX-3, as well as the earlier VX-2.
1200 mahr capacity. It holds a charge fine, and is
basically new. $20

Kenwood SC-13 Vinyl Case
For TH-215, TH-225 and others, with room for the larger PB-1
and PB-4 battery packs. It can also be used with the smaller
PB-2 and PB-3 battery packs, by putting a filler in the case.
Black color. In very nice condition. $15

Bianchi Real Leather Case for TH-215, TH-225, etc.
For use with the larger PB-1 and PB-4 batteries, but can be
used with the smaller PB-2 and PB-3 batteries. This is real
leather, tan in color, and is in very nice condition. $25

Case for Drake TR-33C
This is the black case that fits the Drake TR-33C, and has
cutouts in the back for antenna, power, etc. It includes
the shoulder strap, and is in good shape. $12

Case for Drake TR-22
As above, but for the TR-22. No shoulder strap. $10

Leather Case for Santec HT
This is a real Bianchi Leather case -- not a vinyl case.
It fits most of the Santec HTs, such as the HT-1200,
ST-142, ST-144, ST-440, etc. The real leather case
includes a built in belt clip, plus a removable leather
shoulder strap. $25


Accessories for the Kenwood TR-2400 HT

Kenwood SMC-24 speaker microphone
Fits Kenwood TR-2400 HT and others. This one looks fine
and works fine. $18

Antenna adapter to fit the BNC connector on the HT and provide
an SO-239 connector that will permit a PL-259 to be attached.
This adapter can be used on any HT with a BNC connector. $5

Belt clip for TR-2400 HT, complete with hardware - $8

Wrist strap for TR-2400, and most other HTs - $4

Battery charge cable for Kenwood TR-2400 HT
This is an adapter that permits one to charge the battery of the
Kenwood TR-2400, 2 meter HT, outside of the HT itself. Usually,
one must have the battery inside the HT, but this lets you charge
a second battery outside of the HT. The original charger is used.
It is in good shape, and works fine. $3


Santec HT Accessories For Sale:

Leather Case for Santec HT
This is a real Bianchi Leather case -- not a vinyl case.
It fits most of the Santec HTs, such as the HT-1200,
ST-142, ST-144, ST-440, etc. The real leather case
includes a built in belt clip, plus a removable leather
shoulder strap.
The case itself is in very nice shape. The leather
shoulder strap has not been used. $25

Santec ST-142/144 "Service Pack"
This is similar to a service manual, but Santec calls it a
service pack. It has schematics, circuit explanations,
voltages, etc. $18


Belt Clips:
All include the hardware with the belt clip and are $8 each.
Kenwood BH-2 for Kenwood TH-21 / 31 / 41 series HTs
Kenwood TR-2400
Motorola
Yaesu FT-207
Yaesu FT-209

Wrist Straps for various HTs - $4 each
Kenwood TR-2400
Yaesu FT-209


Service Manuals:

These are original service manuals in extremely good condition.

Service manual for Kenwood TH-21 series HTs, plus most
accessories for this series HT $20

Service manual for Kenwood TH-41 series HTs, plus most
accessories for this series HT $20

Service manual for Kenwood TW-4000 dual bander $20

Service Manual for Kenwood TR-2600, 2 meter HT $15

Santec ST-142/144 "Service Pack"
This is similar to a service manual, but Santec calls it a service
pack. It has schematics, circuit explanations, voltages, etc. $18


Rubber Duck antennas for your HT.
All are for 2 meters, are in good condition,
and are $10 each, unless stated otherwise.

Alinco Stubby w/BNC Connector, 4.6 inches long
Regular BNC, about 6.5 inches long

5/16 inch threaded, like used by Motorola and others
Stubby - 4 inches long

Type F connector - 6.5 inches long

PL-259 connector - 6.5 inches long
HyGain 275, still in original packaging

PL-259 connector - Stubby - 4.6 inches long
Centurion, still in original package

Special for Kenwood TH-21 HT threaded connector
Kenwood RA-6 regular, 6.6 inches long - $15

BNC Stubby for 440 MHz, 3 inches long


Battery charge adapter for Azden PCS-300 HT
This is an adapter that permits one to charge the battery
of the Azden PCS-300, 2 meter HT, outside of the HT itself.
Usually, one must have the battery inside the HT, but this
lets you charge a second battery outside of the HT. The
original charger is used. If you have a PCS-300 HT, you
need this adapter.
It works fine, and looks like new. $3


3 pin mic plug
This is the small 3 pin mic plug that fits the Drake TR-22
mic jack. It is much smaller than most of the mic connectors.
I thought these were completely gone, but one appeared from
a silent key. This one has been used, but should still be
usable some more. $12


Coax Cable with Type "N" Connectors
This cable is made of RG-8 coax and is about 6 feet long.
It has a male type "N" connector on each end. $15


World Map with Kenwood Logo
This map is laminated, and lists DXCC Countries, as
of 1985. Obviously, it is not completely up to date,
but still is a very nice map. Like new. $5


CW Items:

"Code Crash" by Jerome Mintz
This is a VHS video tape that teaches a person the code.
It is a very basic tape, with the assumption that one does
not know any of the code. $12

Cable for straight key
About 3 feet long, with a mono 1/4 inch phone plug on it,
as is used with a straight key. $5
As above, but 1/8 inch (3.5 mm) plug. $5

Cable for paddles
About 3 feet long, and with a 1/4 inch stereo connector
on the end, like used by most rigs. $8
As above, but 1/8 inch (3.5 mm) plug $8


AEA Power Supply
AEA AC-1
"Wall wort" 12 V DC power supply at 1 amp.
Can be used with the AEA PK-232, PK-88 or others.
This unit has a 2.1 mm plug, with the center positive,
so it can be used on many different things that require
12 V DC at up to an amp, such as keyers, antenna tuners, etc.
$15


Phone Patches / Digital Interfaces:

Waters "Universal Hybrid Coupler II" Model 3002

Most of us would likely call this a phone patch, but it
is really much more than that. It does that, but also
will interface with a tape recorder, and permit recording
and play back of on-the-air QSOs. Nothing says that the
tape recorder input must be used that way. Connect the
sound card in your computer in this position, and you
have a very effective interface.

Model 3002 includes a speech compressor powered by a 9
volt battery. The front panel is finished on both
sides, with one side having it set in a horizontal
position, and the other in a vertical position.

This was a "top of the line" unit years ago. One only
found them with top stations such as Collins.

This particular unit is in really great condition.

With paper work for $100.


Heath HD-15 Phone Patch
This is the unit with the VU meter on the left and 3 knobs
that match the SB series to the middle and right. Low or
high Z output to the transmitter. It can also be used as
an interface to the computer for PSK31, etc. It is in
extremely good condition. No scratches or imperfections.
Paper work included for $25.


Weston Precision MilliVolt Meter Model 1
This is an extremely precision meter, with mirrored
scale about 6 inches long. It weighs about 5 1/2 pounds!
It has terminals for scales of 150, 1500, 15000, and
150000 millivolts.
Also included is the calibration information (from 1944)
indicating that it is "dot on" for calibration.
In addition, it is in an extremely nice protective case,
that appears to be real leather.
To put it another way, this is an extremely nice meter!
$80


Coax connectors and adapters:
Prices are per connector. Several of each are available.
These are NOS (have not been used).

BNC male
standard type - $2
crimp on type - $3

Chassis mount BNC female
square mount (uses 4 screws) - $3
screw in type - $4

BNC 90 degree - female to male - $3

BNC "T" - two female and one male - $4

Antenna adapter to fit the BNC connector on the HT
and provide an SO-239 connector that will permit
a PL-259 to be attached. (BNC male to UHF female) $5

UHF Male (PL-259) to BNC female (opposite of above) $5

UHF double female "Barrel connector" (two SO-239 together) $3

Chassis Mount SO-239 connectors (square) $1

UHF "T" connector with two female (SO-239) and one male
(PL-259) connection - $5

UHF female (SO-239) to type "F" Male (as used on cable TV) $5

Type "F" (cable TV) female to BNC male - $5


LARGE Analog Meters:

General Electric Edgewise DC ammeter
0-100 ma scale - Edgewise meter with scale 5+ inches
long and 1.7 inches high. White scale, w/ silver/gray mounting
This is a very nice meter that can be read across the room. $30

LabVolt AC ammeter
0-1 amp scale, 4 inch square meter, $20

LabVolt DC ammeter
0-1 amp scale, 4 inch square meter, $20

DC voltmeter has 3 scales on it - 5, 10, and 25 volts.
It says it is a Niehoff Voltmeter, Chicago, Model T-2.
It looks like 1930s vintage, and is in very nice shape. $28


Very heavy duty chokes, as used to filter ripple in high current
power supplies.
These chokes (inductors) weigh about 8 pounds each, and
are designed to be used in low voltage applications. They were both
removed from power supplies, and are in close to new condition.

One is from a 20 amp power supply. $13.

Another is from a 30 amp power supply. $15.


Prices do not include shipping from Florida.

Thanks.

73,

Ken, W8EK

Ken Simpson
E-mail to W8EK at FLHam.net or W8EK at arrl.net
Voice Phone (352) 732-8400