[Central-Electronics] CE-100V Scope

[Gordon]

On second thought,
   I must be getting it (8mhz signal) to the low level RF board though 
since The Transmitter transmits on the correct frequency.


Gordon
N6WK


On 9/13/2013 5:49 PM, Gordon wrote:
> Hi Lee,
> When checking for a 8Mhz signal at  V21, I do not see it.
> So, I went back and started tracing from the 8 mhz crystal and I loose 
> it in the  Modulator Diode/Coil plugin can .
> I have a good 8Mhz signal going in on pins 5,6,7 & 8, but nothing 
> coming out on pin 3 to the coax that goes to the low level RF board.
> Looks like I need to open that Can up and see what's up.
> I should be able to see a 8 Mhz signal coming out of that can on my HP 
> Freq counter, like I see going in shouldn't I ?
>
> 73,
> Gordon
>
>
> On 9/13/2013 4:24 PM, LeeCraner at aol.com wrote:
>> Gordon:
>> I haven't been following this thread, so I don't know what you've 
>> tried yet.  Separately, I've sent you a schematic of just the scope 
>> portion of the transmitter (actually, the 200V scope circuit, but it 
>> should be the same in you're 100V). This schematic is part (page 19) 
>> of my dissected 200V schematic set available on my website:
>> http://www.emmittsfixitshop.com/Projects_CE200V.html
>> What you should have on your horizontal plates is a demodulated 8Mc 
>> signal.  If you have a regular bench scope, trace the 8Mc signal from 
>> the 8Mc amp plate through phono jack/plug feeding the xmtr's scope 
>> assembly and on through to pins 3 and 8 on the xmtr's CRT.  You 
>> should find your problem in short order.
>> 73
>> Lee WB6SSW
>> In a message dated 9/13/2013 3:40:35 P.M. Pacific Daylight Time, 
>> gordon at n6wk.com writes:
>>
>>     I received the Correct CRT tube today.
>>     I installed it in great anticipation, but when I turned the radio
>>     on and
>>     it warmed up, The Vertical Line is still there  :-(
>>     I noticed that V21 is an 8mc Amp, So should I be seeing a 8Mc
>>     signal on
>>     Pin 9 of that tube?
>>     I notice the Focus control works, the Intensity works but the width
>>     doesn't seem to do much .
>>
>>     I am baffled !
>>
>>     73,
>>     Gordon
>>     N6WK
>>
>>
>>     On 9/9/2013 4:39 AM, Paul wrote:
>>     > Just curious, what mode are you testing the scope in? You
>>     mention "when you talk" so are you only testing it in a voice mode
>>     like AM or SSB? What do you see if you test it in CW mode? If SSB
>>     mode, have you nulled the carrier, as you adjust the null controls
>>     you should see the vertical trace reduce in size until it becomes
>>     a pinprick in the center of the scope.
>>     >
>>     > Keep at the restoration, took me over a year to do my 200V and
>>     now it is my main BA transmitter paired with my 75A-4. I use the
>>     200V far more than my KWS-1, especially since I added the 160m mod
>>     to the 200V. That's where the KWS-1 really falls down, no 160m
>>     although the 75A-4 has 160m. What was Collins thinking?
>>     >
>>     >
>>     > ________________________________
>>     > ______________________________________________________________
>>     > Central-Electronics mailing list
>>     > Home: http://mailman.qth.net/mailman/listinfo/central-electronics
>>     > Help: http://mailman.qth.net/mmfaq.htm
>>     > Post: mailto:Central-Electronics at mailman.qth.net
>>     >
>>     > This list hosted by: http://www.qsl.net
>>     > Please help support this email list: 
>> http://www.qsl.net/donate.html
>>     >
>>
>> ______________________________________________________________
>>     Central-Electronics mailing list
>>     Home: http://mailman.qth.net/mailman/listinfo/central-electronics
>>     Help: http://mailman.qth.net/mmfaq.htm
>>     Post: mailto:Central-Electronics at mailman.qth.net
>>
>>     This list hosted by: http://www.qsl.net
>>     Please help support this email list: http://www.qsl.net/donate.html
>>
>
> ______________________________________________________________
> Central-Electronics mailing list
> Home: http://mailman.qth.net/mailman/listinfo/central-electronics
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Central-Electronics at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>