[Boatanchors] DC Voltmeter Calibration

[David C. Hallam]

I have reached the point where I don't believe my Metex DMM ME11 comes 
even close to an accurate voltage reading band-gap reference or not.  I 
tested several fresh AA alkaline cells and they all read 1.651V.  I 
don't trust its readings any further than I can throw my 2KW amp power 
supply.

David
KW4DH

On 1/7/2016 3:36 PM, Al Klase wrote:
> CORRECT ANSWER!!!
>
> Modern DVM's all contain band-gap references. These are semiconductor 
> devices that use quantum-physical principles to generate a know 
> voltage. They are much more accurate than anything else you're going 
> to lay mortal hands upon. Sit down with a AA cell, and compare two or 
> three DVM's. You'll be amazed.
>
> In my case:
>
> $300+ Fluke 87 1.588V
> $70'ish Escort 1.589V
> $11 Ebay cheapie 1.592V
>
> A VR tube or Zener diode won't even come close.
>
> Al
>
> Al Klase – N3FRQ
> Jersey City, NJ
> http://www.skywaves.ar88.net/
>
> On 1/7/2016 1:38 PM, D C _Mac_ Macdonald wrote:
>> I'd bet you'd get a lot closer than what you have already
>> by using a cheap (sometimes even free) digital meter
>> from Harbor Freight as a "standard for comparison."
>>   * * * * * * * * * * *
>> * 73 - Mac, K2GKK/5 *
>> * (Since 30 Nov 53) *
>> * Oklahoma City, OK *
>> * USAF, Ret'd 61-81 *
>> ** FAA, Ret'd 94-10 *
>> * * * * * * * * * * *
>>
>>
>>> Date: Thu, 7 Jan 2016 13:02:11 -0500
>>> To: boatanchors at mailman.qth.net
>>> Subject: Re: [Boatanchors] DC Voltmeter Calibration
>>> From: boatanchors at mailman.qth.net
>>>
>>> A quick and dirty way that will get you a lot closer than +/- 45 VDC 
>>> would
>>> be to rig up a VR-150 running at about 20 mA.
>>>
>>> In a message dated 01/07/2016 10:25:07 AM Central Standard Time,
>>> dhallam at knology.net writes:
>>>> I obviously need to calibrate my DC voltmeters.  I was setting the 300
>>>> VDC B+ on my signal generation after some repairs.  I used 3 
>>>> voltmeters
>>>> and got a spread of 45V among the 3 of them, low 285V and 
>>>> high330V.  The
>>>> low was a VTVM and the high  DVM.  What is a good standard to use that
>>>> won't break the bank to acquire?  I used to have some mercury 
>>>> batteries
>>>> but they are a no, no any more.
>>>>
>>>> David
>>>> KW4DH
>>> Robert & Susan Downs - Houston
>>> wa5cab dot com (Web Store)
>>> MVPA 9480
>>
>> ______________________________________________________________
>> Boatanchors mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/boatanchors
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Boatanchors at mailman.qth.net
>>
>> List Administrator: Duane Fischer, W8DBF
>> ** For Assistance: dfischer at usol.com **
>>
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to ark at ar88.net
>
> ______________________________________________________________
> Boatanchors mailing list
> Home: http://mailman.qth.net/mailman/listinfo/boatanchors
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Boatanchors at mailman.qth.net
>
> List Administrator: Duane Fischer, W8DBF
> ** For Assistance: dfischer at usol.com **
>
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to dhallam at knology.net
>
>
> -- 
> There are two possible outcomes: if the result confirms the hypothesis, then you've made a measurement.
> If the result is contrary to the hypothesis, then you've made a discovery.
> Enrico Fermi