[ARC5] 24vdc power

[Tom Lee]

Yes, it's too bad that we don't have a section for FAQs (or do we?). 
Your solution probably ranks the highest in SAF (spousal acceptance 
factor). It's also the optimum way to handle both the startup surge and 
the steady-state requirements.

-- Cheers,
Tom

-- 
Prof. Thomas H. Lee
Allen Ctr., Rm. 205
350 Jane Stanford Way
Stanford University
Stanford, CA 94305-4070
http://www-smirc.stanford.edu

On 9/4/2022 13:06, scottjohnson1 at cox.net wrote:
> I wish I saved my old posts on this subject since it comes up every so
> often!  I find the best way to operate rotating machinery that once operated
> in a mobile environment is to replicate that environment.  SO-
> Get a power supply that can handle the full load current and float an SLA
> battery across it.  Size of the battery and power supply is proportional to
> load, but in your case, a 10-20 A switcher. Set to27.5 V (for normal indoor
> ambient temperature)
> Less for hotter, more for cooler, but in the range of 27-28V.  For your 10A
> load, 12V 7AH SLA batteries would do nicely. (Two in series).  Increase AH
> capacity proportionately for higher current loads.  Amazon and eBay have
> plenty of inexpensive switcher that will work, just don't buy the REALLY
> cheap ones, unless you like the acrid smell of burning components.
>
> -----Original Message-----
> From: arc5-bounces at mailman.qth.net <arc5-bounces at mailman.qth.net> On Behalf
> Of Charles via ARC5
> Sent: Sunday, September 4, 2022 10:23 AM
> To: arc5 at mailman.qth.net
> Subject: Re: [ARC5] 24vdc power
>
>> Hey guys,
>> What's everybody using to provide 24vdc for your military radios? Two
> 12vdc supplies in series?  Home brew?  Do they make a 24vdc switching supply
> that will handle 10 amps or so?
>> Thanks for your input,
>>
>> Richard kn7sfz
> Anything with a dynamotor needs about five times the motor nameplate current
> for the starting surge...
>
> I got a 2 KVA three-phase 115V 400 Hz rotary converter at a flea market but
> nothing I had was big enough to start it (rated at 27.5VDC at 115 amps!)
>
> So I bought a 20 VAC, 5 KVA toroid transformer on ebay, a BFBR (big bridge
> rectifier), heat sink, a 220,000 uF cap, meters and shunts, and brewed up a
> 24-28V 120 amp brute force supply with 240 VAC input. THAT starts the
> converter all right. It doesn't even blink at smaller dynamotors :)
>
> -Charles, WB3JOK/0
>
> ______________________________________________________________
> ARC5 mailing list
> Home: http://mailman.qth.net/mailman/listinfo/arc5
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:ARC5 at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: https://www.qsl.net/donate.html
>
> ______________________________________________________________
> ARC5 mailing list
> Home: http://mailman.qth.net/mailman/listinfo/arc5
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:ARC5 at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: https://www.qsl.net/donate.html