[ARC5] 10 meter BC-454 - more

[brianclarke01 at optusnet.com.au]

	Hang in there, Ken, 

	I think you're doing a grand job. I'm really looking forward to your
end solution. 

	73 de Brian, VK2GCE. 

----- Original Message -----
 From:kgordon2006 at frontier.com
To:"Arc5 mail list" 
Cc:
Sent:Thu, 14 Feb 2013 10:10:25 -0800
Subject:[ARC5] 10 meter BC-454 - more

Over the past few days, I have "solidified" the coils and their
included slugs.

I also did some careful adjustment (using my Millen GDO), and
rewinding of 
the RF amp plate/mixer grid coils (L2/L3) by 1) eliminating the 9 turn

interwound RF plate coil (L2), and winding a 14 turn (from the
original ARC 
documentation) separate coil above the mixer grid coil (L3),
positioning it 
identically to the original coil, and 2) adjusting the spacing of L3
to tune it 
with the C4D and C4F "centered" (1/2 open) to 28 MHz.

Result of solidifying the coils was to reduce, but not eliminate, the
ringing, 
but it did eliminate the "jumping" of frequency. The jumping was
obviously 
caused by the loose slugs.

Result of reworking L2/L3 was a vast increase in the gain through the 
system. Obviously, the original ARC method of coupling L2/L3 is far
more 
effective than the CQ-magazine-suggested method.

Interwinding L2 with L3 was suggested by the original article which
stated 
that doing so would increase RF gain. Instead, this seemed to cause L3
to 
tune VERY low, and instead vastly REDUCED the gain. I suspect that the

very close mutual coupling had something to do with this, and that the

reduced gain was caused by inability to tune the mixer grid coil to
the proper 
frequency.

I have about exhausted every normal reason for the ringing, except
two: 1) 
the tuning capacitor (which I am almost convinced there is nothing
further I 
can do about), and 2) the bypass capacitors I used to replace the
can-caps 
around the mixer stage.

I used some small high-quality rectangular-shaped dark-orange-colored
.047 
MFD 400 VDC caps to replace all the shot can-caps, and mounted them 
right at the tube sockets as stiffly as I could. However, the mixer
stage, which 
also contains the HFO, appears to be very sensitive to movement of any

component associated with it.

Therefore, I plan to "solidify" every possible bit in that area with
some of 
Mike's coil dope.

At this point, I am almost convinced that the ringing problem is
centered in 
the tuning capacitor. One clue is that even very slight movement or
touching 
of the front-panel, or the box that covers the tuning cap, or the
tuning knob, 
or the coax that connects to the antenna connector results in
significant 
frequency shift.

Some of this, of course, can be put down to the 10X increase in the
HFO 
frequency, but not all either. Techniques that work well at 3 MHz,
don't 
always work as well at 30 MHz.

BTW, the original ARC documentation concerning circuit values
(capacitance 
and inductance, and turns on the coils) provided by one or two of our 
members here, are almost exactly what I am now using. I will re-post
those 
details when I have finally run out of patience with this....thing....

Kenneth G. Gordon W7EKB

"Courage is being scared to death but saddling up anyway."--- John
Wayne

______________________________________________________________
ARC5 mailing list
Home: http://mailman.qth.net/mailman/listinfo/arc5
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:ARC5 at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

-------------------------
Email sent using Optus Webmail