[ARC5] [Milsurplus] If You Need a Regulated Low B+ Supply

[Dennis Monticelli]

Well, you're talking about following or replacing the slow switcher with a
linear reg.  Sure you can do that and it works well, but that will cost you
the efficiency you were after in the first place by going with a switcher.

Providing feedback for regulation is usually best, but the key is at what
freq do you sample.  Do it rapidly and you have more EMI to content with, do
it slowly and then some other means is needed to deal with the poor dynamic
regulation, be "vitamin C" or a secondary linear regulator.  No free lunch
I'm afraid.

Dennis AE6C

On Sun, Feb 14, 2010 at 11:35 AM, J. Forster <jfor at quik.com> wrote:

> Not at all.
>
> If you want regulation, there are a number of ways to do it. IMO, the
> simplest would be a FET or BJT version of the "Beta-C" circuit with the
> capacitor replaced with a Zener or Zener string.
>
> You could also regulate the inverter input and feed back an output sample.
> Isolation of the B- line is usually not needed, unless you are stacking
> supplies. Some exceptions are the R.1155 and WS19 HT2.
>
> -John
>
> ===============
>
>
>
> > True, you can slow switch at 60Hz but if dynamic load regulation matters
> > it
> > can become an issue.  You would have to rely purely on big oversized caps
> > vs
> > the feedback loop to hold the voltage steady in the presence of CW or
> > voice
> > peaks.
> >
> > Dennis AE6C
> >
> >
> > On Sun, Feb 14, 2010 at 11:14 AM, J. Forster <jfor at quik.com> wrote:
> >
> >> One solution to the EMI problem from switchers is to use a low frequency
> >> square waves, of the order of 60 Hz, rather than 10s of KHz. This
> >> enables
> >> you to use much slower rise/fall switching times and conventional
> >> filament
> >> transformers run backwards. They are bigger and require bigger HV caps,
> >> but are a lot quieter.
> >>
> >> Best,
> >> -John
> >>
> >> ================
> >>
> >>
> >>
> >>
> >>
> >> > While the diagram says "new" this part and the associated circuit
> >> dates
> >> to
> >> > 1991 when it went into the early GM airbags.  I know because my work
> >> group
> >> > designed it.  However, it is still sold along with a plethora of other
> >> > "Simple Switchers" which have gone through five generations now.  If
> >> you
> >> > go
> >> > to the National Semiconductor website you will a cluster of
> >> easy-to-use
> >> > design tools that allow virtually anyone to design the switching reg
> >> they
> >> > need right on-line.  All the popular configurations are covered.  You
> >> can
> >> > then order the components along with the PCB from the distributor link
> >> or
> >> > just roll your own by buying the chip from DigiKey.
> >> >
> >> > BTW, you can still stack "common-ground" DC/DC converters by feeding
> >> them
> >> > raw DC from independent windings on the transformer.
> >> >
> >> > Remember that most switcher circuits are not designed to have low
> >> enough
> >> > EMI
> >> > to guarantee happiness in our radios.  Pay close attention to short
> >> lead
> >> > dress, good grounding and use shielded inductors vs the cheap solenoid
> >> > types.  For best results, extra input & output filtering and a metal
> >> box
> >> > may
> >> > be needed.
> >> >
> >> >
> >> > Dennis AE6C
> >> >
> >> > On Sat, Feb 13, 2010 at 11:50 AM, David Stinson <arc5 at ix.netcom.com>
> >> > wrote:
> >> >
> >> >> This cute little circuit is an example of the kind of DC/DC
> >> >> converter you cannot stack, since in and out have a
> >> >> common ground:
> >> >>
> >> >> http://www.nbglin.com/dc.htm
> >> >>
> >> >> Still a neat circuit, though.  I'm gonna get me a
> >> >> couple to use as "Borg Implants."
> >> >>
> >> >> 73 Dave S.
> >> >>
> >> >> ______________________________________________________________
> >> >> ARC5 mailing list
> >> >> Home: http://mailman.qth.net/mailman/listinfo/arc5
> >> >> Help: http://mailman.qth.net/mmfaq.htm
> >> >> Post: mailto:ARC5 at mailman.qth.net
> >> >>
> >> >> This list hosted by: http://www.qsl.net
> >> >> Please help support this email list: http://www.qsl.net/donate.html
> >> >>
> >> > ______________________________________________________________
> >> > Milsurplus mailing list
> >> > Home: http://mailman.qth.net/mailman/listinfo/milsurplus
> >> > Help: http://mailman.qth.net/mmfaq.htm
> >> > Post: mailto:Milsurplus at mailman.qth.net
> >> >
> >> > This list hosted by: http://www.qsl.net
> >> > Please help support this email list: http://www.qsl.net/donate.html
> >> >
> >> >
> >>
> >>
> >>
> > ______________________________________________________________
> > Milsurplus mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/milsurplus
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Milsurplus at mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> >
> >
>
>
>